This was just too easy to not be worth it. This was just the TC2 kit from gokartusa. We were flying around, climbing hills we couldn't make it up before. Lots of fun for sure.
So the TC2 kit I ordered from gokartsusa arrived today.
I followed the instructions and the install went quick but it doesnt line up.
The piece piece on the jackshaft seems to be out away from the engine too far. I get everything on and the belt doesnt line front front to back, it bends to...
It has come to my attention that the proper engine mounted drive unit for this model may be called a v-plex or it could be a farbanks morse. Which one is correct and what can I interchange with?
BTW the model 250 is the hardtail model with 6" wheels and the big "dovetail" axle brackets...
Ok, so I bought a Comet Torq-A-Verter for my mini bike and only problem is that when I slow down/stop then let off the brake I start to speed up and sometimes it's a lot or just a little. I've stopped completely before and it started going like 3mph. Is my engine just idling too high for the...
Ok, so I'm going to my second phase of my project. I am going to install a torque converter, it has a size 40 sprocket to go to the rear wheel. Is there a simple sprocket change that bolts onto my DB wheel? It was suggested on one of my other posts that my centrifugal clutch may be burning up...
Picture #1 shows the inside sheave not retracting fully so the kart wants to move instantly.
Picture #2 shows the rollers and springs have "jumped track".
Picture #3 shows the inside of the cover. I see no obvious isue with the sheave or cover so what is causing the rollers to do this? I've...
Guys:
I have a 1970 Rupp Enduro with a torque converter. Ordered the belt from that specific year, apparently that year had a different size than all the others, but my question is what is the easiest way to install a new belt on the bike? Obviously just slip it on the rear, but do I need...
Does anyone know the exact size for a 1970 Rupp Enduro Torque Convertor belt? Apparently, it is not like the 71-74, it is a different size. Just need to know before I order one and I need a Rupp person to set me straight. Any help is appreciated.:shrug:
I have a super rare NOS Broncco Renegade torque conveter cover for sale. It has some shelf wear, but is in great condition...Perfect for your restoration! $100
Just wanted to post this for info for anyone who is looking to buy a TC belt or is having issues with one they purchased. Would also like to know if this is even a potential issue?
I just received 3 new Gates 6061 "Sportline" belts that I bought online (as a substitute for the original Comet...
I started this by asking a question but I figured it out so I'm changing it. My torque converter was stuck on and I tried all sorts of things to get it off. Here's what I figured out.
Spray some PB blaster all around it and wait for a bit for it to soak in.
Then I put a small washer inside...
Comet 40 Series Torque Converter. The following parts are for Sale, they are New and have Never been used. I originally purchased them for David and my Super Powell Project. Please PM any questions or if your interested in purchasing a part.
Comet Model 44C Magnum Drive Clutch 3/4" Bore...
I need to rebuilt the engine for my Lil Indian Hellcat but can't get the torque converter off to get to the inners of the motor. Does any one have any suggestions, I was thinking a little heat but I don't want to ruin anything.
I am building a frame and want to make sure I leave ample amount of room for a torque converter. How much space is needed in between your driveshaft and jackshaft?
Bonus question: There seems to be a lot of different torque converters out there... what is the best bang for your buck? My mini...
I bought this Super Bronc torque converter setup from Gustavo. I was hoping to use it on my El Burro but it just didn't work out.
It has everything you need. I started to clean it up a little, but it will still need some cleaning, just dirty and a little rusty. Includes the 1" brake handle and...
No idea who made this. 3/4 inch drive looks complete, but I don't know anything about these.:shrug: Driven has a piece broken off.:sad: $40 shipped b/o. Paypal preferred.
Okay that is my ??? I'm in an argument with brother and he says that it is impossible for a TC to hold down revs . We are talking about a NRracing limited mod with a 44 driver and a 7.5 inch 40 driven . He says that it will rev to 8000 with it , i don't know but want to hear from the experts on...
I can't for the life of me get this friggin' torque converter bolt off:
I've got the engine off and, with a ratchet holding the flywheel bolt in place, try to turn the torque converter bolt.... but it absolutely will not budge, despite repeated WD-40 treatments. I've even tried hammering...
Hey guys I picked up a Tri-rod with what I believe is a Comet setup on it. This is my first belt style torque converter and I spent a few weeks reading up on its assembly and operation. After that it became very evident that the system had been mickey'd with quite a bit. I'm leaning toward...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.