Hello All,
New member here, I'm in the process of converting an old Manco Rustler 3 wheeler into a fat tire bike. I got the rolling frame years ago and hadn't really done anything with it. I had put a 5hp Tecumseh powersport motor on it and putted around the yard and then it sat. Decided...
I was thinking of running e85 in my 212 Predator, but I don't know how much of a problem it is to convert it to e85... what will I need to do?( just a though)
I'm curious about converting my predator 212cc motor to run on E-85 fuel.
What's the pro's and con's?
What all would I have to do to convert it?
Has anyone else already did this and your thoughts on your own motor afterwards?
I got an older 5hp Briggs. So I picked up a "new style coil *magnetron* with an aluminum flywheel, I will no longer be running points ignition, my question is; the keyway don't line up in the same place....is this due to the difference in the ignition set-ups, or is my motor so old they have...
I have this little generator with the Walbrow bowl carb on a 3.5 horse flatty.. It uses a nice aluminum intake manifold.. Problem is the main jet is not adjustable, and if I want to use the generator, I gotta wire the choke like EXACTLY 23 / 59 shut, or it won't run..
The power went out, and...
I just got a hotrod raptor engine with an hl348e tillotson carb setup for alcohol. This is the first tilly carb i have owned and im looking for some help setting that carb up for gasoline. I dont know anything about this carb yet but if anybody has some info on whether or not it can be done or a...
I have an hs40 engine that is non ball bearing on the pto side. I have a ball bearing crank and side cover from another engine. Is that all I need to change it over during a rebuild?
does anyone know how to do this? theirs a video on youtube but i was wondering if anyone has used a mower engine for a minibike and how well it works.. if you guys have any advice please help. im interested in doing this but im not sure how good it will work.
if you guys have any pictures...
I should start off by saying I am competent welder and machining things is not a problem so this project is well within my means.
I have a bone stock doodlebug that runs fine but that's not why I bought this.
I have your standard HF 6.5 hp motor that I want to swap out.
These are the things I...
Started out as a electric scooter found in trash with junk batteries. So i say why not try rigging up a 3hp briggs to run on it already did a lot of work. So here is some pics. Today ordered 10 tooth clutch 41 chain a twist throttle and cable
new member have read a lot of posts here finally reg...
i have a I/C engine that had a gear reduction. its a model 133252-0049-01 wondering if i could swap cranks put a 3/4'' shaft and do i need to change the side cover? if any one has part numbers that would be helpful! looking to put...
I was pulling my hair out trying to convert all this stuff for my sprocket...this link is a conversion chart...pretty handy for us newbs!:wink:
Maryland Metrics: CONVERSION CHART: FRACTION/DECIMAL/mm
so i have a honda g200 on a minibike and it seems to backfire way too much. when i go full throttle and then let off it backfires not once but like non stop. i did some reading on it and thought that it was running too rich so i leaned it out which made it abit better. i also read that timing...
Anyone done this? What ould have to be done to convert to E85? I thought it might be cool to run this fuel since the station down the street now carries E85 and it would be cool to shave the head for compression and run the E85 to keep the evil detonation away.
I know I would need a carb setup...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.