h25

Itchin to do up some motors (been awhile now)so i picked up these two today. Lovin the lil H25 as it looks barely used after I started wiping all the crud off it. Hopefully i get some time tomorrow and pop the head off. H25 is H25 25196H 1972 and the other is HS40 55459E 1975.

Mini bike correct 1972 Tecumseh H25 off an Alexander Reynolds mini bike. It has a 3/4" by 2 1/4" tapped and threaded crank and is a rear exhaust engine. I put a new carb and fuel line on it to make sure its still alive. It runs pretty decent for an old engine, idles good, accelerates good.There...

Hey all, Thought I'd make a little restoration thread as I haven't done one in some time. I'm currently working on an early 60s H25 that was partially stripped by the previous owner and thrown in the corner of a shed. Many years later it sits on my work bench, in more than a million bits...

Looking for a pickup/ignition coil for a H25 Tecumseh engine. Model # H25 25045C and serial # 444 02639. Anybody familiar?? Please, see pics

I have an h25-25188g motor and unless I can find another similar motor I am planning on doing a rebuild. My question is that should I replace the crankshaft bushings and what are the tolerances of these bushings? It appears that they are not being produced anymore and would much rather reuse...

I need a replacement for my H25 that has a bad camshaft, crankshaft (both have stripped gears) and at least one stripped thread for holding the head on the block. I would prefer another H25 so I can swap all the new parts that i installed on the old one or a larger HP one that I can also swap...

Hi its whizzerkid . I am looking for a number plate for a Skat Kitty it is a Tecumseh 2 1/2 hp and needs the H25 plate that gets put on the side of the cover Thanks Wayne

I'm trying to get the H25 on my Rupp Chopper running before I proceed with my build and not matter what I try it will not run off idle. It will sit there and idle all day long but the second you give it any throttle it start to pop and sputter like it's flooding and will not come out of it. If I...

I'm trying to get the H25 on my Rupp Chopper running before I proceed with my build and not matter what I try it will not run of idle. It will sit there and idle all day long but the second you give it any throttle it start to pop and sputter like it's flooding and will not come out of it. If I...

Hey all, I'm looking for a pull-start Shroud to fit an H25/H30/H35 and the U-shaped metal piece that goes behind the flywheel that the shroud bolts too. The shroud needs to be the 60s-70s round style for motors with the coil underneath the aluminium type flywheel. Looking for a shroud in...

Everything in the picture is included. Not gonna do anything with it. I think some one should though. Here's some more info. http://www.oldminibikes.com/forum/tecumseh-engines/120872-performance-stock.html $75 shipped

Hey all, Did a deal at a swapmeet recently. $5, I scored this old beast for :laugh: This is an old H25 Tecumseh. I know this because the intake manifold is very small on the inside. It didn't come with a shroud so I'm not sure what year it is. Maybe someone can tell me by looking at it?? It's...

Hi' Thanks for responding, I'm currently in need of a Round Tecumseh Air Filter Cover , It came from engine H25-25193H Model 2067B Thanks JIM

I am in need of one for Model 2067B # H25- 25193H Thanks IJG

Hi' Thanks for responding, I'm currently in need of a Tecumseh Air Filter Cover , It came from engine H25-25193H Model 2067B Thanks JIM

Hey everyone, I started my freshened up H25 engine yesterday three times and it ran great. I just fired it up today and it started screeching from the shroud. I pulled the shroud off and tightened the flywheel and the screws that holds the recoil on. I started it back up and it only makes a...

H25 side popper $100 plus shipping H35 side popper $100 plus shipping I also like cat parts

Picked this up yesterday and started work on it right away. Like I do t have enough projects. Lol Started to strip the frame. Ran out of daylight so worked on the motor for it through the night. Got it running then tore it down. Plan is to paint it white. It's a h25 just not the side popper...

Not sure of this motor. Looks to be a early h25 with a diaphragm carb. No exhaust. Has spark and compression. 5/8 shaft. No throttle controls on shroud. $45 plus shipping

1970s Sears Tecumseh H25 w/Steel Liner, NOS Never Run