I just got a Hilliard 10t #40 clutch on the engine i got for my project i would like to trade it for a #35 3/4 clutch either 12 or 13 tooth is fine, Ill cover shipping on mine if you cover it on yours.
Hey everybody, been awhile (THANKS, A.D.D...)
Just built myself a killer 4'X4' worktable for the minis & other upcoming projects - I just needed a damn work TABLE and not a work BENCH, you know? The whole thing took one evening and only cost my wife around thirty bucks or so!
First up...
I decided to go with a torque converter and no longer need this.
I went up an down the street 2 times so it is pretty much new.
Just like this one:
http://www.northerntool.com/shop/tools/product_200310374_200310374
$35 shipped by paypal takes it. USA only.
I just picked up a hilliard Fury, it came with a 16t and 17t sprockets. My question is, would I be able to buy the 41 pitch sprocket from OldMiniBikes warehouse that said it would fit a hilliard clutch? I don't know if the sprockets interchange between the extreme duty clutch and the fury.
Thanks in...
Ok...I have 2 brand new clutches from Hilliard. From my best guess they are more for compressors or something of that nature. I am not sure anyone will have a use for them...but figured I would list them here in case. They are 7/8'' shaft...but take a V-belt. One is in the box..the second is...
Just installed a new Hilliard clutch to my 6.5. It is only held on by a single bolt thru the end of the crankshaft and a lock washer. Problem is....I haven't figured out how to tighten the bolt enough as the center of the clutch starts to spin. How do you hold that sucker still?:crying:
I was given a Hilliard kart clutch with the sprocket just chewed clean off of it. I figured it was a good deal but now i see sprockets from $15-19? Seems kind of pricey? I have bought new clutches for $29 that use real springs as opposed to the C shaped springs these use.
Any thoughts on...
Building a go kart. Has a 420cc predator motor and a 1" bore 17t hilliard clutch. Went to test fire the motor and adjust the idle screw and noticed a good amount of smoke coming from the clutch. Shut it down tested again a few days later with idle lower, not smoking nearly as much and idles...
:cursing:
This is my hilliard clutch after only 3 weeks of use on my bone stock HF clone'd manco thunderbird. All the teeth sheared off the sprocket. (yes i know the bushing isnt on it in the photo.)
Gonna go this weekend and try to get a store credit from tractor supply (have all the...
For sale I have my almost new Hilliard Extreme-Duty Corp V-belt clutch.
I got this for a project but ended up selling it off. So now I have a clutch thats been mounted on a engine once but never run or used. Has a few scrapes from being out of the packaging.
The Clutch is a 4 shoe/4 spring...
Hey, Well i was riding today on this trail in the woods about to go to this dirt pit thing. And i notice that my clutch starts to act up. Starts to stick. So i had to bring the kart home. I took of the housing and i seen that one of the springs where bent and the housing brushing had shatter...
I am going to need a new clutch for a Heathkit Boonie that I bought last fall and I am sick of the standard Max torque clutches.
I have seen these Hilliard's advertised, but have never used one.
like this one:
Hilliard Extreme Duty Minibike/Gocart Clutch 3/4" #35: eBay Motors (item...
I have a briggs I/C engine with a nearly new Hilliard Fury inferno clutch. The clutch has a 10 tooth 40/41 sprocket on it. The engine also has a jackshaft plate setup and a Backing plate as well. gas tank is clean, just the outside has surface from being bare metal.
The engine runs great! I am...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.