main

Finally found the elusive main jet!

Genuine mikuni vm22-133 round main jet and replacement genuine mikuni hex main jet

Vm22-133 round main jet with o ring

Aside from linkages, are the new style Pulsa-Jet carbs the same for 3hp to 5hp? For example...a model 135202 with detent choke vs. my model 90202 with spring loaded choke? I want to put the 5hp carb on my 3hp but dont know if theyre calibrated differently.

I just picked up a 5hp kart racing engine which is setup for race fuel, I just need to replace the main jet. What size would I need and are there different types. Here's a pic of the carb. Thanks.

Looking for some main jets size 150-200 and pilot jets 17.5-30 Will pay with paypal right away if your trusted and you can send them in an enevelope as long as they work, it don't bother me:laugh: and by chance if anyone comes across a 4J13 needle or 0-0 249 needle jet

That extruded aluminum series carb that the OH318 series came with is famously shoddy. I've got a decent sized shop, tig welder, and lots of metal odds ends pipes etc, so slapping a new carb on is no sweat. I ordered a replacement for a honda engine of similar displacement and am having a...

Would you just stick the bottom one back in the carb or would u change it anyway. In comparing it with the replacement i dont see much of a difference at all. I dont see an edge or squaring off at the tip the way the manual shows whens its bad. I just feel the original parts are better than...

Hello all, I was just curious to see if there any fellow musicians here. I am guitarist / bassist. I started playing guitar back when I was 10 back in 82 when I got my first nice acoustic guitar and learned my first three chords. Since then I have been hooked! I am mostly into rock, southern &...

Found her up in Minneapolis between main 1 and main 2 tracks. I figure that it must had been stolen and abandoned or some kid got tired of pushing it and left it to get hit by a train. Either way, it was not suppose to be there and now it is mine all mine :thumbsup:

Okay, I'm stumped. It's not for a mini, but I know you guys can help. I've got spark. It will run when I prime it (or on starting fluid), but it dies shortly after. I have cleaned the carb vigorously two times. There is no leak between the carb and block, and I know the main jet is clean because...

I need a main jet for a DB-30 97cc Someone drilled the jet out way too big and it just floods out. Does anyone have one they can part with?

New old stock mufflers 1/2" pipe thread, will thread into your old Tecumseh 4hp and others. Main muffler part is 3" long and 1-3/4" across the main body. 1/2" pipe nipple is 1" long. Has chips in paint from shelf wear. $45 bucks shipped for three, paypal only please...

I was looking on ebay for a jet holder for my vm22 since I misplaced the one for mine and I came across this.... hopefully it fits the bowl on my carb and works well.. This would make tuning the carb easier that having to keep trying different main jets..... Vintage Motocross MX Precision...

I installed a high flow air filter and header on my Predator 420. Now I need to rejet a Predator 420 carburetor, where do I start. Any help would be greatly appreciated.

I need a 6.5 hp clone stock main jet for $5.00

Need some advice on what size main jet I should be using? I have a 6.5 clone with stock carb with larger emulsion tube, intake, governor removed, aluminum flywheel with 4 degree of advance, billet rod, stock piston, gx160 head, SS valves, retainers & keepers, 18lbs springs, chrome moly push...

Does anyone know what the sizes of the different marking stamps are on an intek carb?

how much play (side to side) is allowable i just bought a used 5hp & find there's a 16th of an inch play or more?????

Would appreciate any help on this one...... I bought a used mini recently that has a Tec OHH60 6 HP "Powersport" engine that is about 2 years old. It had a high performance KNN-type air filter and a custom straight pipe exhaust. I do NOT know if the main jet has been increased in size. (From...