mounting

I measured this tank and to the best I can tell, it's 8-1/4" long and 3.18" (3-1/4"?) wide. It was on an HS40 cart engine I picked up recently, but I don't know if it was original. It was definitely on there for a long time if it wasn't original. The brackets and gas cap are included. Inside...

Would anyone have a nice close up picture of the 1969 rupp kickstand in it's mounted position? Would be greatly appreciated. Underside of frame specifically. Regards, Joe

Hello all, I am finishing a restoration on an Alsport Tri-Sport RTS-SL and I need to drop the diff and replace a broken diff bolt and sprocket mounting nut but I want to buy averything ahead of time. So I was wondering if someone could tell me what size, length and thread diff case bolt and...

Does anyone know the length of the 1970 chain guard hex mounting standoff. I can't find mine and need to make one. Thanks

I have three Tecumseh air filter canisters for sale. All three have both pieces (found a back plate for the white one after I took the pictures). Black and red canisters have both sets of the original mounting screws, white one has only one screw holding the two pieces together. Notice the...

I had bought an MTD roller to use as a donor to freshen a survivor up that I have but decided not to. Hopefully there are some guys that can use some parts to freshen theirs up or complete them if needed. I did not want to clean anything as everyone has different means and ideas of what they do...

I'm honestly not sure what this is worth because I've never seen them for sale, so I'll throw out a number -- $95 shipped OBO. Please feel free to make offers. Bother are in good condition, but could use some fresh paint. The threads on the connecting rod are clean, and the rod is straight. The...

Boonie jackshaft mounting plate with nice jackshaft and newer sprockets. Mounting plate is original. Sprockets and shafts is not. Single speed setup. Good parts. $60 shipped. I can email or text photos. Located in west michigan.

Twenty bucks, I couldn't say no. There's a plate between the handle bars that was sprayed over with green paint, and then some kind of mounting plate (headlight, perhaps?) was screwed over it. Across the bottom, I can clearly warns you about 'off-highway use only', that sort of thing. Across the...

I have a 79cc predator engine, and I'm looking for a way to get generator power directly from the engine. My goal is to power a 12v electrical system (headlight, tail light, brake light and battery), in the simplest way possible. I know that if I attempt to hook an accessory wire directly to the...

Why is it such a pain to get the haves of a two piece rim off the tire on a mini bike? In the process of mounting a new tire on a new rim I put hole in the tube so now I need to get the rim halves off the tire to put in a new tube and it is proving to be almost impossible. Before mounting...

I was going thru some of my motors tonight and came across this mounting stud for a boonie clutch cover. Has some chain rash, but nothing terrible. Has the double threaded end screw too. Unfortunately, the outside threads are pretty beat up. Asking $25 shipped. PayPal preferred. Thanks!!

Here is a set of Western Flyer SS300 Forks for sale. They are slightly tweaked but look like they could be easily straightened. They also have the long mounting bolt and nut. Asking only $10 plus shipping?

I have a seat from a Stellar minibike. In great shape! $45.00 plus the ride needs a little work on the mounting bolts send a PM if you can use...and trades are always welcome!

The kids want to put one of their 6.5 predator engines on the manco kart but the pto is not long enough so the sprockets can line up. I was looking at one of the pmr adjustable motor mount kit. which holes line up with the engine or the factory mounting plate. I can see how this would work on a...

I have a 8hp Briggs from a snowblower I'd like to use for a project I'm working on. The motor case does not have mounting hole bosses cast in it to mount the torque converter. Anyone see a problem with drilling and lock nutting the bolts thru the case? I'm hoping there is clearance inside

I recently purchased a 212 predator motor and the bike I have had pre drilled hole in the mounting plate where someone mounted a B&S. the existing holes are very close to where I need the 212 holes need to be. So close that I can't drill new ones without overlapping the old ones. I have seen...

I'm Restoring a 1970 Maverick Mini Trail and Instead of rebuilding whats left of my original seat pan it looks like a Z50 seat might fit and you can by those new. Would someone be willing to measure the width and length of the seat Pan. Also the Height of the actual seat from where the material...

I have 2 of these motor mounting plates. These were from go-karts but are pretty universal for any real application. About 8" wide and 10" long. $15 each shipped?

Hello, I need some help on how to wire up a kill switch on a 1966 Briggs 3 HP. I'm mounting the switch to the bars.