non-hemi

wtb black mamba cam for non-hemi predator.. no rush.. for a budget build

will the stock 5.2" non-hemi predator push rods be long enough if I am going from stock rockers to championship rockers? Or will I need longer ones? Thanks

Hey yall. Ive got a non hemi 212 on my mini bike and Im getting parts up, dont want to go real crazy but ive got billet fly wheel, mod2 cam, 26lb springs, jetted carb, cone filter, and a nice header. What rod from ARC should i use the standard or plus 20? not planning on doing any head work or...

NR-Racing 285 0607p camshaft - for predator non-hemi, new never used, you need to clear the block for this camshaft I believe... going to build a big block instead.. 60$ shipped... its 80$ + shipping on Nr-website.. will need stronger valve springs 26lb+ springs for this camshaft, great...

Im looking to build a non hemi predator with RTC-8 head. It's going to be put on a asphalt go kart that will be used for parking lots and maybe on the streets in a subdivision. I would also like to use pump gas. So far I'm thinking: governor removal ARC flywheel 308 cam (102 centerline)...

Good Evening Everyone, I am looking for some troubleshooting help with using a stock carb on a modified preadator engine. First, this is not on a minibike, but a motorized bicycle that I race occasionally here in southern california. The rules for this engine are stock rod...

What's the best parts to put on a 69727 non hemi 212cc with the rtc-9 head? I ride a 2-speed auto motorized bike that currently tops out around 55mph. The engine currently has a 19mm slide carb, 4* adv timing, removed governor, removed fan and shroud and set up as a rope start, and now has a...

Can someone point out the difference between the Predator Hemi vs. the non-Hemi engine? I'm planning to purchase a 212cc Predator, but would like to know if there's a benefit to one engine over the other. Does the "Hemi" have a hemispherical combustion chamber design similar to a Mopar hemi...

Pulled out and rode my CAT with a non-hemi pred the other day. Has maybe 4 hours total run time on it. After a day of sitting, I had nice oil puddle on the floor. Couldn't see where it was coming from. Anybody else have issues with oil leaks on stock engines--could it be the case or seals?

What site has the cheapest connecting rods for 212cc? And does it matter how long the rod is? And whats the effects off a longer rod and will i have to do any machining?

I have some questions about some mods to a non hemi that i have been thinking about. First, would porting intake and carb do any good? Second, is there a different head you can put on a non hemi to increase combustion? And third, what are your thoughts about putting a 49cc nos kit on a non...

What is the best over all cam on the market that i wont spend too much money on. I was looking at the CM grind cam but not sure. Thanks

How do I tell what springs I have ? Measurements? if I order 22lb springs can I use stock everything else? all I've done so far is air,exhaust, re-jet, timing key. if other parts are needed will 18lb allow stock parts ? I have a non-hemi with some hemi internals so determining...

Does anyone make a ring compressor? I am wanting to put engine back together. Is it possible to install piston with out ring compressor? Thanks Jeff

I`ve read alot of the build up threads and I`m guessing if I`m gonna buy a new Predator I should get the hemi version. I was hoping maybe someone had pics of the two different heads. I`m still not sure what the actual difference is. Thanks in advance.

So I've finally decided to bite the bullet & buy a 212 for my upcoming, ham-handed bastardization of a ultra-mega-super valuable, worth 6-figures GENUINE 1985 Kawasaki KX125 frame (made only for one year!) :wink: So before heading out to Harbor Freight, what are the differences between the two...