I need to get my hands on a governor arm (of all things) so i can get my next project up and running.
needs to be the two piece type.
Here's what I need:innocent:
Here's what I got :facepalm:
want the 2 piece aluminum sprocket 53 to 56 teeth # 35 chain, fits the 6 hole drum or hub
also want 1 to 3 seats
5" slick or rounded tread.
koollee_909@yahoo.com
email me, i dont use this site too often.
Ok so the other day i thought "man, i really do miss my weed eater bike".. so i went to have a second look at my Homelite 25cc trimmer engine..
I have two of these actually.. the one on my bike, i took it off in the first place was because I thought the cylinder flaked on the inside due to...
I've never messed with them before. I'm assuming this is a two piece:
I took the bolts out, took the "star" and the sprocket/drum off, and still can't get it apart. I REALLY don't wanna damage the wheel prying on it with screwdrivers to get the tire off. should I just cut the tires off? I...
I got my new tires yesterday for my rupp sprint with 6" turbine wheels but I ran into problems because the tires were all distorted and each center was way off from the other side .
For those of you that are not familiar with rupp front wheels they are made up of three pieces 2 rims and a...
I found a little piece of Tecumseh Gold at the scrap yard today. Took me about 5 minutes to figure out what it was, because I've never seen one in person, but when I did I nearly shat my pants.
It only cost me $5.30, a bit cheaper than what they go for on Ebay.
It has only a few minor...
Its a 2pc Lil Indian rolling frame. I was just wondering if these are worth very much money??? And i would also like to know if there is a way to find out what the year of it is? thanks
I'm a newb and lost the part that connects the govenor control arm to the throttle shaft. The bar that pushes the throttle when you pull on the throttle. I included a picture I found online here, but can't get it to paste on here so I included the link to the thread. Thanks in advance!
Hey everyone, I need one two piece Manco 5" aluminum wheel for my kids' go kart. I have one wheel that has the mounting hole ripped out on each half, unfortunately it's not the same hole on both halves. Basically I have one bolt holding the 2 halves together. I'd take a whole wheel or even some...
As the title says - looking for a one piece steel 6" rear steel wheel with a 60 tooth sprocket. (it is for an Arco EZ rider)
Must be straight and in very good condition (including the sprocket). The paint is no concern.
Contact me via PM.
Thanks in advance !
'Sup guys.
I got another question. Has anyone ever taken a two piece wheel and bolted the together with silicone, and used a tubeless tire on it? I personally don't see why it wouldn't work.
I got my rear tire here, which is a tubeless 13x5.00-6, and I am making a spacer for my 2 piece...
its not mini bike related, but its bike related so i figured i would start a thread of the progress. ive been working on making a CF piece for my friends harley. its the piece that goes around the gauges and runs the length of the tank(not sure of the real name of the piece) .so far i have the...
I have Rupp 6" turbine wheels with the a one piece sprocket w/the brakes on the interior... 5 1/4 brakes... I have looked everywhere and cant find it. The previous owner had the motor mounted of center and made the sprocket look like a saw blade.. Thanks Justin
I want do some tire swapping on some spoke wheels, easily doable here in the garage or is this best left to the "pros"? I don't have any tire tools except for a plastic set for a bicycle, and I doubt they are gonna cut the mustard! Is it worth buying some tools?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.