piston

Which way does the arrow point on a HS50 piston? Towards the front or towards the valves? Thanks.

Well I took the mini bike it out for about a 30 minute ride full throttle and then just slow cruising speed also. Any way when I shut her down for about 10 minutes and went to kick it over and there was no compression. So i took off the cylinder head cover cap off and the cover on the left...

I have just acquired an italjet that I had as a 4yr old. It needs new rings (39.2mm). Do y'all have any recommendations for a supplier. I have messaged a seller on ebay that is offering Caber rings, his feedback is very good. Any thoughts on Caber rings? It has been pretty difficult...

i have a honda gx200, just getting started building it up tonight, i hope. i need someone to help me out with installing the new rings, i have never done it before. there are 4 new rings in the set and i have no idea which ones go where, or how big the gap should be or where the gap should be...

my 5hp briggs only turns over just under half a rotation. i am not sure exactly how to about aproaching it, because i dont want to take apart the camshaft. any suggestions?

I thought I'd start this thread to document different engine, piston, barrel and head by using photos. :thumbsup: My clone GX160 with dish piston and 14cc head:

Have a 3.5 briggs 91232 with a lot of piston slap at the beginning of throttle as the rpms go up the slap goes away. Any suggestions? Also i have a 91202 short block just sitting. Does Either one of these 2 motors have a bearing on the crank? Is there a way to look at the outer case to...

i was wondering if anyone could tell me which honda engines come stock with a flat top piston. i have several honda gx160s for parts but have not cracked them open yet. also i have read here that lots of people like to run a +.20 arc rod with the flat top piston in the blue hf clones, my...

Put in new ring and piston. Compression is at 65lbs holding. Checked and rings were placed correctly. With proper gap. I replaced the valve springs. My old springs were different heights and the motor specs call for different springs. Comp cams sent me the same spring for each valve. ? The...

Im building an open motor out of a 6.5 briggs intek 206cc engine that i had. parts are used but in good condition. crankshaft with gear, rod, std piston. $60 shipped.

Which way does the X on the piston face? or the hole in the rod? There is no arrow on the piston

Hi, I would like to find a piston that was pulled from a Briggs 5hp military engine that looks like it is new. Please PM me if you have one for sale. Thanks, Al

Looking for an obsolete +.030 over Genuine B&S piston for a Briggs 8 hp I/C......pn# 393880 Will pay dearly for a NIB piston...:grind: Walt

I figured out the hard way that a GX160 and a GX200 piston aren't entirely interchangable. Since I already have a 160 flat top piston, I thought I'd save some money on my 200 build. Guess that was a mistake. The piston fits the bore, but the rings from AGK don't fit the stock GX160 piston...

Who makes a stock pin diameter forged piston for the arc long rod? What is the strongest rod piston combo for nitrous?

I have a new never used stock take off piston and rings off the older style item 96549 for sale $15.00 shipped to your door...paypal or M/O.

I am looking for a Briggs Long rod and Piston combo. It needs to be standard size piston. Wiseco and an Arc or Horstman rod to go with it. 4.500, 4.475. It is a steel bore RIII block, so I don't need it to be chromed. I am building a beast with a Dyno 115 cam. Let me know what you got...

I need a piston, rings, wrist pin and clips for a 1971 beta premier bebe. 50 cc 4 speed. Also need a carb. Thanks

I have some parts off a new HF 6.5hp clone I removed to build and was going to trash can them, but I thought I'd post them here first and see if anyone wants them. I have the Flywheel and Fan, Connecting Rod, Piston without the wrist pin or rings, and assorted governor and Throttle parts. If...