running

need a 8 or a 10hp tec motor for my dads T777 buffalo trail bike needs to run no junk it also needs to be a older model no new OHV setups send pics and a price to me n a Pm or here on this thread

Hi all, I have a 3HP briggs flattie. It has the pulse jet carb, with the tank mounted beneath. It had sat for a long time, I got it with a used Bonanza. Anyway, I took it apart, cleaned it, cleaned the head, cleaned the carb, etc. It runs, but it is hard to start, and it dies a lot...

Hey guys, i stopped by my high school to see my old auto shop teacher and he had a bike sitting in the shop, he gave it to me for 10 bucks and told me something along the lines of "someone gave it to us, and i think he said all it needed was a new spark plug" before going out and buying a new...

I have an old Sears tractor that was running fine until today. Went to start it and it won't stay running. It will only run with choke fully closed. If I try to open choke or idle up it stalls. It will run smooth at first and then after about 30 seconds the governor starts to run the throttle up...

i want to sell the frame or the complete bike.F/S just frame or just 3.5hp or running manco minin bike.......

Kind of interested in putting one of these in a Ruttman for my 7 year old daughter, Figured it woul have plenty of power to haul her around. Anyone use one? Any issues? How tall is the motor? Is it 3/4" shaft? Not a lot of info on the site. Here's the link. - Harbor Freight Tools - Quality...

I drilled out the main jet in my stock clone carb to .035 which is supposed to be a size 89 or 90 jet size. after I installed the jet back in the engine would not run wide open. It was running very rich puffing black smoke and running rough almost like the choke was 1/2 open. The only mods to...

I was on a go kart site and noticed that they said you could not run a clutch with a tire bigger than 15" . Does this hold with a mini bike, if you are going to run a clutch and sprocket? What size tire will give me the most stability for off road riding while still keeping a clutch and...

Like the title says...I need a good running or NOS 3HP early Briggs for my early Lil Indian......ANy help wouldbe greatly appreciated.....thanks alot guys......Louie

I have a Cat 400 and its got a Briggs 3.5 HP engine. Im not very clever with these motors, but the engine starts up smoothly, but dies under load. I have new gas, good oil and a clean air filter. Any possible suggestions for me to check to get this running good. Thanks!

I been looking for a steel replacement cam for my HS50 and OHH60 but havent had any success in finding any other than new and they are in the $50 and up range so I was considering getting a cam from Batman along with valve springs... I was just curious if anyone has used any of his cams and how...

ok guys I have a 5 hp briggs that will start if I put a tiny bit of gas in the carb but wont stay running. I put on a new diaphragm and carb to gas tank gasket, cleaned out the carb and blew out the passages with compressed air ect ..... This was a $5 engine with a stuck valve ...I'm sure this...

I want to add a jackshaft on my minibike to replace the one someone cut off. :( - Anyways, Where is a good place to get a 5/8" or 3/4" flanged (2 bolt) bearing that is not a ton of money? Any other type of bearing that works good? I don't believe I have anyplace to run a pillowblock, There are...

I got my little buddy back running good again. The last time you seen this bike the crank was broken, Now he's back, and with just a little more power than before. Check out this video. YouTube - Hector vs Faustino

My 2 project minis are coming along, now I want to buy a good, finished (for now anyway) neighborhood rider. I'm in Camarillo and can pick up anywhere in So Cal. 5 hp, a good brand, no junk and no rip-offs! PM me or call at 805 889 1932. :scooter:

I just ordered a 24mm vm Mikuni carb.I was wondering if any one had mods close to mine to let me know if this carb might be to big right now,or if I can get a base line jetting start. 6.5 clone, 18cc head milled .080, RLV header 1.2 rockers.Oh, and a ARC rod but that has nothing to do with...

Want to try and experiment with a different gear ratio. basically test some new speeds on the mini before making major engine modifications. What were some of the low end hp ratings you guys were able to get it going with?

Need to fab up some pegs, but she is a runner, fast as hell too!

I'm new to this so please bear with me: I just bought my kids the DB30, It ran great and started on the first pull, but now it's hard to start and wants to stall out after one good rev or run, and with the choke all the way closed it has no power. Any thoughts ?

Just picked up an old K&S Hornet with the original Tecumseh in it and need to get it running. Its missing the rope starter, the carburetor and the spark plug wire has been cut once before. What should i do? I was gonna drain the oil and replace it, then change out the spark plug then just patch...