steering

Hello, I have a little play in the front fork of my motovox mbx10. Anybody know what size bearings are needed?

Hi all, Putting a Sears Roper together and coming to the realization that the steering tube has been bent forwards, reducing the rake. Forks are straight (now) but when I put it all together there appears to be very little rake. The fork hits the steering tube when I turn the bars full left or...

Any tips or secrets to removing the fork bushings on my '67 Rupp Continental? I don't want to bugger something up that is hard or impossible to fix. I've soaked them with PB Blaster, but they are not budging. Just get a bigger hammer? And...if I get that far, any tips on re-installing the...

Hey Fellas and Gals, I have a mini I am working on that has been ID'd as a Joe type... When I was taking off the forks/handlebars and I was surprised when I didn't see any bearings in the neck tube. Is this normal? The neck tube has a 9/16" ID. And the bottom handle bar cross bracket...

Hey guys, starting to buy replacement bits for my DB (currently at the powder coaters). I can't seem to locate a source for the steering bearings H.R.M.B.com doesn't stock them and OldMiniBikes was closed for phone calls, but I didn't see it on their site either any help greatly appreciated. Thanks

Ridding my Baja doodle bug with predictor hemi motor . It's kinda more shaky on front. Like to add a steering dampener to the system. I saw one doodle red with steering dampener but that guy would no pm me. I use to make them for my race outboards and sold a few. I like to make one for my...

Interesting discovery last night. I bought 2 Baja MBs taken apart and in boxes. I was putting one together and discovered that one of the forks on the steering tree was damaged. I ordered another and it showed up yesterday. Maybe others know this already but...... The replacement steering...

Searched a few older posts here on steering stabilizers but not seeing much experimentation. Looking to calm-down a wide-tire front end. Need an adjustable damper with at least 90mm piston travel. Prefer not to resort to a Gixxer unit and/or crappy pocket-bike pieces that don't have the...

looking to connect with man from RUSSELVILLE KY JUST LEARNING TO E-MAIL AND SEND PICS still working on steering damper thanks for info from all here is so pics first build tried 3hp but needed more power 212 is dangerous added bars it is a blast wish i started looking at mini bikes years ago...

looking for help thanks ahead of time i have a efenal missile single bar frame looking to add steering damper any input on this will be great thanks

I need a clutch cover and neck bearings for my BAJA HEAT 165. Anybody?

Never seen one of these actually put on a minibike, but you could be the first to do so. Nice vintage 14" steering wheel, with white rubber coating. Chrome is good. Rubber is slightly marked up and is off white. Has a couple extra holes drilled. Probably for a steer assist knob. Asking $40...

On my Cat 400X the pipe where the steering bolt goes thru is worn out causing the bars and wheel to go fore and aft. I took it all apart and did not see any bushing. Is there a replaceable bushing or what can be done to fix my issue ?

Apparently this is a bonanza scout mb250 that I have, and the steering shaft in the forks seem to have a little wobble in them. Feels worn out, and will also slightly bind when turning. I was wondering, does the shaft have bushings or something that can be replaced?

Good day everyone, A couple questions in regards to the steering neck of the forks with the spring under the neck itself, not sure how to describe it better than that. Are these strictly used for bushing type necks or can they be used for bearing necks as well. If used with bearings will...

Here's my reverse trike I've been working on It has a gy6 150cc engine , hand controls , and rear storage . My future plans are windscreen, Motorcycle front tires /brakes, possible suspension and enclosed soft top. She will easily do 65mph and cruises comfortably . Parts are from several...

Howdy,We just replaced all 52 steering bearings in the front handle bar/goose neck area.. Does anyone know how these should be adjusted properly ?? 5/32" bicycle bearings steel chrome.. Any help great appreciated.. Thank you, Marilyn.. :hammer:

Anyone know where I can get some better quality wheel bearings and steering knuckle bearings for the MB200? Not just OEM replacements, but better sealed and maybe better material bearings?

After riding my Baja for several hours, I started noticing that the handlebars wiggled a little more than they should. I tried tightening down the nuts on the bottom side of the top plate of the triple tree to make this go away. However, those nuts were as tight as possible, yet the wiggle was...

Need to replace the steering wheel on a kart I am building for my grandson. All reasonably priced steering wheels now seem bolt to a splined hub. This kart has a 3/4" Dia. shaft with a drilled cross hole for a bolt to attach the wheel. It is proving difficult to find a smooth bore hub. Any...