What tilly carb works on a Honda/predator. Mostly stock. Would be replacing stock parts with billet. Just don't know what carb to look for. Gas of course.
Well I finaly got him to bring that nanza here to EAST TN CUSTOM MINIBIKES AND BAD ASS EVERYTHING . The all new raptor I have built him is going on the nanza .
The motor has a dyno 107ss cam , billet rod and flywheel . Also the new dual bearing block has had the ports cleaned up and eyebrows...
Hey guys, I was installing a HL Tillotson on my Briggs and I got a question. What is the fitting in the intake manifold for?
Sent from my iPhone using Tapatalk
A tilly gas HL 365-B carb with 2 adapters. One adapter fits a 5hp briggs and the other fits a Briggs Animal/Intek. Just took it off an animal engine and was in good working condition.. Also included is an EC cable holder and air cleaner and adapter
Price is $75.00 shipped. Paypal only...
OK so i bough a 304 Tilly gas kit from smallenginecams.com and it
doesn't run very well. i have a black mamba cam with 1.3 rockers 11.5
compression and stock sized valves with a home port job i just flared the
radius. i will be upgrading to a 18cc head with big valves 27mm intake 25...
i was having this problem a few years ago with my 5hp briggs flathead wher the pull start handle would randomly pop off and the motor shuts off. so i took the flywheel shroud off and put oil in the starter clutch, and thought it was fixed. than i put it away for a wile and now i put a new tilly...
I'm having some issues with my carb. While its running it leaks out of where the air filter adapter is. I can see it coming from inside the carb. Is this normal?
Making a push here to get the Jack Spitler bike to Windber...still missing a few pieces...
Here's the velocity stack I'm trying to match......it's sort of pressed or formed thin aluminum sheetmetal with a fine screen rolled into the lip. Fits the small bore Tilly.... I think somebody drilled...
I just got a hotrod raptor engine with an hl348e tillotson carb setup for alcohol. This is the first tilly carb i have owned and im looking for some help setting that carb up for gasoline. I dont know anything about this carb yet but if anybody has some info on whether or not it can be done or a...
I have a 5hp Briggs with a pipe, ARC rod and a large Tilly carb. The bike runs fine but when I stop it gas runs out of the carb. What settings (number of turns) should I be using. The motor has a Walbro pump on it but a stock cam--is the cam the problem or carb settings? Thanks Bill.
For sale..304wx Alky Tilly. I pulled this out for another member..but he is goin a different direction now. It was built by Korndog and set up for a medium build clone/Honda motor. It has been sitting on a shelf since I got it and the previous owner has about an hour of run time on it from...
I can use two if I can get them...butttt they need to have the bigger flange on the carb side with approx 3/16-1/4" of material above and below the bolt holes on the carb flange...... opening on the carb side needs to be approx 26mm / 1"
For sale I have a HL292B Tilly. I bought this a while ago and just never used it. I am not likely to use it at this point I think so I am selling. Everything is there and intact. These things are dense, very well built for sure. Ditch that bowl carb and get yourself one of these reliable...
what would happen if i put a 388a tilly on gas in a stock clone with ported head and exhaust and 10.8 springs? dont really want to buy my cam yet but im going to
I'm selling this fresh never used Korndog built HL189F with EC intake and air filter adapter. Still has the choke intact for reliability. Built for a stock to mild 5hp briggs or 3.5hp briggs with some detuning. Asking $100 shipped priority mail paypal or postal money order.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.