fitting

  1. J

    Benelli Volcano Tank Fitting

    Does anybody know how the fuel tank is fixed to a Benelli Volcano? I have just bought one and it looks like some sort of strap is missing that attaches the tank at the rear to part of the frame? Any advise or a photo would be great. Thanks Jeremy
  2. C

    Pulse fitting on hemi valve cover

    Where on valve cover did you drill?
  3. UnorthodoxCreat

    Can I change this carb fitting?

    Anyone know if it is possible to change a fitting like pictured below? I fitting that went up at a 90 degree angle would fit much better on my bike but I don't know if it's possible to change out and if so where can I get the fitting I want?
  4. L

    Mikuni intake with pulse fitting for clone gx200

    35$ shipped image post
  5. 1stBxMopar

    Valve Cover W/Pulse Fitting

    GX 200/Clone- Valve Cover W/Pulse Fitting and Gasket... $10.00- plus shipping
  6. lostinbaja

    Need Help with my new Tecumseh carb.

    I recently purchased the Tecumseh carb for my HM80 and it has a hose nipple besides the fuel line nipple. Can someone tell me what it's for? I have determined the nylon fitting is for the fuel line. I don't know what the aluminum fitting is for.
  7. jays0n

    Hydraulic Brake from HRM banjo fitting size?

    Hey everyone, hoping someone else has done this and knows the answer. I have the hydraulic brake setup from hot rod mini bikes on the DB30 trike I just built. It fits with the included brake line but I had to run it in a way I really don't like the look of. I can get a replacement line in...
  8. thebronc4019

    Fitting for import gas tank

    I recently purchased on of those gas tanks that comes with the motorized bicycle kits. I a using it on an Alexander-Reynolds build. Does anyone know the size and threads on the outlet at the bottom of the above-mentioned tank. I would assume that they are metric because I am sure the tank was...
  9. markus

    Bonanza zerk fitting problem

    I pulled the MX off the shelf to start reassembling the frame: the zerk fittings almost look like they arent even threaded??? Or if they are its a fine thread and they got trashed upon removal. I only have one original, I'm pretty sure the one on the headtube got trashed when I pulled...
  10. K

    Fuel Fitting - must I use the same replacement

    I am tearing down the carb on the Bird Thunderbird I am working on:hammer:, and will need to replace the fuel fitting on the carb. The plastic piece is broken off and the metal tube is still attached:facepalm:. I don't think I should have any issues getting that out, but I was wondering if I had...
  11. Clayon

    Pulse fitting on intake manifolds?

    What's the purpose of a pulse fitting on the intake manifolds? I know that you would run a line between the crank case breath to that fitting, but what does this do?
  12. L

    clone valve cover with billet spacer and pulse fitting

    40$ shipped can also mount an exhaust brace onto the bottom of the valve cover etc.. pretty sweet
  13. T

    Pulse fuel pump help?

    Can someone explain to me when this is needed and how i would install it? i have a the Predator engine and just did these mods: KN style filter Velocity stack adapter Manifold spacer (with Pulse fitting) #90 main jet 140 Emulsion tube Header and briggs muffler Racing plug Do i...
  14. C

    pulse fitting location?

    hi guys, i was wondering if it would be ok to put the pulse fitting in the center of the carb adaptor.i have a 22mm mikuni with a carb adaptor,and i want to drill and tap it on the top of the adaptor and center it in the adaptor,will this be ok?
  15. jandj

    HF Clone pulse fitting question

    I know they make pulse fittings that thread into (one of) the oil fill holes for Briggs and the yellow clone. Does anyone make one like that for the blue clone?
  16. S

    Need fitting help asap

    I have one of the Baja sports MB 200 bikes and i have the chance to pick up a Tecumseh 8hp super cheap, i am wondering if i will be able to mount the motor to the frame of my bike with hopefully no or very little modification, Its the Hm80 motor...
  17. P

    Big Block Tecumseh exaust pipe fitting

    The fitting fits a big block 5 H.P. Tecumseh. May fit others. 14.95 each. Only the fitting is forsale, the pipe is just to show what it came on. The fitting is NOS.
  18. johnf.357

    valve cover pulse fitting place?

    need to drill hole for the brass pulse nipple,on the 5 hole clone valve cover.. it looks like the best spot is right in the middle of the "o" in the lettering,(there is nothing behind that area to interfear... anyone agree?disagree?
  19. korndog

    Pulse Fitting

    Say, where are you all pulsing your fuel pumps from? I've seen them on the valve cover but is there anything wrong with using the governor rod hole? Any preferences?
  20. minimotor

    Fuel Fitting Replacement

    Has anyone replaced the fuel fitting on a h35 carb? Does the new one just press in?
Top