flathead

3/4 SHAFT... .ASKING $50 LOCATED IN SO CAL.

I bought this old bike and it has a 3.5 craftsman (tecumseh) off of power washer. It didn't want to fire, it would run for a second then die so I figured it was the carb. It has one of those chokeless primer bulb carbs, so I swapped it out with another carb he gave me that has a choke on it. The...

I've got an old g200 flathead motor on a log splitter thats in kind of bad shape. Just wondering if anyones ever done anything with them. I know it's got a steel sleeve bore. I was thinking of using this motor as a eventual replacement on my super stock db 30. I got it running about a year ago...

Im building a briggs flathead and i wanna use a different cam then the 94ss...so my question is whats a good cam that will give me low end and mid-range power without being hard on my valve train. list of mods are below if it helps -billete rod -new stock valves -stiffer springs -3'...

whats the differance between flathead and OHV head engines? can a cam from a flathead work in a OHV?

im a newbie to flathead briggs and these pulsa-jet carbs that are mounted to the tanks. so bear with me please. The long tube would obviously be the pickup tube to the carb. Filling that small metal bowl the smaller cast piece of the carb sits in and thats where the carb is really sucking gas...

I am looking for a cheap 5hp Briggs flathead, would prefer if it was stock, because I don`t want to pay extra for the mods. Show me what you have and I will see. Depends what the parents say.

Anyone know of any instructions on rebuilding or tuning this carb.

Would a 8 Hp Briggs & Stratton I/C engine be a good engine for a large style Big tire mini with a TAV2? I am mainly worried about excessive vibration and lousy thorttle response and idle quality from the down draft style carb, any ideas?

:shrug:how do i change to electronic ignition ?...a 5hp briggs..?

This is a great working gas carburetor off of a briggs raptor 5hp kart engine. I measured the bore and it looked to be .710. It is set up with all the linkages for a go kart, minibike, barstool etc. It has a nice aluminum air filter adapter. The tank is in great condition with no dents and is...

hey i have a 5hp fun power briggs flathead motor, i was wondering if i could get a gas gauge for it? it has a stock gas tank carb ect.. if it needs power or sumthen im putting a 12 volt motorcycle battery on my minibike anyway so that would be fine.

I am looking for a FINNED Billet Flywheel that I can use on my 5hp Briggs Flathead. Let me know what you got (send pics if you can), and how much you want for it shipped to 01604, Worcester, Mass. My e-mail is rollinsgl@aol.com Thanks, Jason

Good running briggs 5hp that will need paint! what you see is what you get. sold as-is looking to get 90+shipping? Thanks, James I just got a new job so i wont be on much today, sorry Thanks, James

Does anyone know of a crank from another engine that will fit in a 5hp flathead? looking for a longer stroke without the $400 price tag?

WOW :drool: Found a Kohler 18 horse Magnum HORIZONTAL crank at the junkyard today... :drool: And it looked like TOTAL crap, so I tore the heads off and a LOT of rusty water poured out of each.. :ohmy: But the walls wiped clean pretty well, and both rods are unbroken.. :deal: So I carry the...

I have a good used 4.500 rod that needs bearings. I want it gone. It WILL NOT work in a stock 5hp briggs using the STOCK piston. I'm asking $25+ shipping or $30 shipped. I'll have pics tomorrow.

After going over the checklist, I seemed to have about 95% of the parts to build this engine. Heavy Duty 4.475" Billet Rod, Wiseco Piston, Walbro WB Carburetor, Single Bearing Aluminum Bore Engine. Assorted Parts, alot of which I found in storage.:smile: Every single part of...

new 00-3 cam for 5hp briggs flathead $45 shipped or would accept trade