mitsubishi

  1. C

    Compatibility on Mitsubishi 6hp

    I have a 182cc mitsubishi GT600, 6.0 hp and I was wondering if this Predator Performance Air Filter with Adapter and Upgrade Jet would fit correctly, or does it have to be a 212cc 6.5hp to fit.
  2. thomas3120

    Looking for Exhaust manifold - straight pipe for my Mitsubishi GT600

    Hello, I decided to remove the stock muffler and make/weld a straight pipe that fits inside the left rear shocks, stays clear of the tire and exits rear left under edge of the rear fender: I know the welds aren't pretty, using an Arc welder w/rods and also still learning. Tough time...
  3. tundrabeagle3

    6 hp mitsubishi head needed

    I need a head for my 6 hp Mitsubishi motor. please pm me with ur price I am located in Corona , CA
  4. tundrabeagle3

    which one 5 hp briggs or 6 hp vangaurd

    I have a 5 hp briggs that has a 20 mm slide carb on it that I am running on my firehawk with a tav2. I also have the 6 hp Mitsubishi ohv that came with the firehawk which is the same a the 6 hp vanguard but have been waiting for parts (new pushrods , and rocker adjusters) that are being special...
  5. FordGalaxy

    mitsubishi

    I have a nice 4 hp mitsubishi, honda clone. I'm wondering if a 26mm mikuni is to much carb for it? What about a 5 hp IC briggs flat head. Engines are stock, just looking for a simple way to use a bigger tank on my tote gote.
  6. tundrabeagle3

    6 HP Briggs vanguard /mitsubishi

    I got a 6 HP Mitsubishi motor that is the same as the 6 HP Briggs vanguard . It came with my Firehawk mini bike. I would like to make it faster and have been searching for racing parts online. I have found a billet rod for it but have not seen any hp cams or billet flywheels that can fit this...
  7. Valocalrep

    Mitsubishi 6.0 hp

    Ok so friday my roommate picked up a FireHawk mini bike and it came with the stock mitsubishi 6.0 hp motor. He said he had it running a few months before my roommate got the bike but im not sure if i beleive him. Here is the issue. I dumped the tank, cleaned it, flushed and cleaned the card and...
  8. N

    Mitsubishi gt 600 6hp-Engine Upgrade options?

    I went for a ride a few days ago. The road we were on is a dirt road with a 30 mph limit. It's all graded with little traffic. There were a couple small hills and the TAV took me up them with zero trouble. My motor is sputtering a little at peak rpm's, so I'll be checking that out this week...
  9. jeep4me

    Mitsubishi Engine on a Toro Snowblower?

    I bought a Toro 2-stage snowblower a month or so ago and the guy said it had an 8hp Tecumseh engine on it. When I got to his place I noticed right away that this was no Tecumseh. I couldn't tell what kind of engine it was, there are no manufacturer markings on it anywhere. I did a little...
  10. 6hp mitsubishi

    6hp mitsubishi

  11. minigonzabel

    project mini chopper

    Hello everybody this is my mini chopper that I am fixing up. Bought it from a guy not far from where I live for $35. I took seat and gas tank off to find the neck was cut out. Took accesories off that was not needed. Fixed and reinstalled the front hydraulic brake. Installed a headlight. My Dad...
  12. R

    Comments on a Mitsubishi 6hp

    Anybody have any comments on a Mitsubishi 6hp engine? Are they any good? There's one on Craigslist for $20. I thought I'd put it on my Manco and put it up for sale.
  13. W

    6 hp mitsubishi engine

    i have a 6 hp mitsubishi motor with about 4or5 hrs on it . it is about .15 inches tall . has anyone ever put one on a mini ?i know i will have to stretch a frame ,just wondering about throttle hookup ,goveror removal ,the shaft is perfect 2.25 by 3 quarter keywayed . if i remove the tanki...
  14. FordGalaxy

    mitsubishi engine

    Anyone know anything about the mitsubishi gt 400 4 horse engine??? I'm thinking of replacing the 4 hp briggs on my tote gote with it.
  15. P

    6.5hp tav/cvt

    hi, I'm new to the forum (first post). I was wondering if anybody could help me find a CVT or TAV for my 6.5hp mitsubishi? The engine was on a firehawk but now its on this custom bike i built. I dont have the 200 bucks for a real torque-a-verter so I was wondering if there were chinese clones i...
Top