part

Vintage Briggs Gas Cap 69961 | eBay I guess that all of us have put a giant bid on some ebay part just because we had to get it no matter what the cost. I bought this old 5.75 hp briggs a few years ago and have been trying to find a gas cap for it ever since. It uses the old style two...

i have a rupp black widow part out that im selling, i do not have the motor or handle bars, extra front springs, few misc parts what ever is in the picture and 2 black widow carbs parting out if you need anything pm me, Will only take money orders, will sell the entire rolling bike for 200.00...

Ok this is a bad picture i took offline cuz im not at home right now but on the back of the motor by the airfilter (i think) there is 2 tubes that connect to a black cyliner and the cylinder has a tube running out the bottow with a black cap on it. Well first off What is it lol. 2nd is it...

Hey guys. It's me again. I'm back to messing with this guy again. I'm curious if anyone else thinks that it's knocking or is it just me being a mechanochondriac? I have another tec here that I'm going to try to get working to see if it makes the same noise. The throttle feels and sounds nice...

Hey all, I posted a Tecumseh shortblock on the parts page. As I stated there I have picked up about 5 big boxes of older NOS Briggs parts, with a few Tecumseh parts. There are all kinds of parts from carb kits, mufflers, point armatures, screws, rings, etc. Also a ton of different head and...

Taking a bike down today and I broke a lower eyelet on a Sebac shock. its the non tapered lower style. This ones off a heathkit, I think I usually see them on the bigger bikes. I need just the eyelet if you have used one of these shocks for parts or something or if you got a single shock...

Part out. I will list what's left. Located in Brewster, NY 10509. Block and side cover, includes side cover bolts, cam and lifters and all gov parts. $25 plus shipping. Pull start and shroud, includes all the ducting and the funky shield over cylinder. Extra long cord! No handle. $15 plus...

Picked up a yellow clone from a karting buddy for really cheap. Has ARC billet flywheel, cam, header, and filter/adapter. His class didn't allow a billet rod. Well his side cover came loose during the race and the engine is locked up solid. I will be able to salvage the flywheel, header, and...

3hp tecumseh part out. only thing it doesn't have is a crank shaft and carb

Parting this out. Blower housing and recoil $25 shipped. Any other parts contact me. Will pull it apart if necessary. Paypal preferred.

Parting this motor out. Blower Housing $20 shipped. Aluminum flywheel $35 shipped. Any other parts just ask. Best offer on any or all.:thumbsup: Paypal preferred.

Hello everyone i`m looking for my FANTIC gokart the aluminum rear part of the rim that goes on the rear axle either for the disk brake are the chain side every help is welcome please keep in mind i`m oversea i live in the netherlands wfg Bé

I need the wrist pin for an HS40 piston.

My engine(s) info: H25 250736 5074 03215 H25 250736 5074 03154 Need good carburetor and coil mount plates (need 2) -

Parting out or all. Located in Brewster, NY. Rod started wearing on face. Was going to rebuild with a billet rod but that takes money and time. You know the rest. Block and side cover with bearings and seals. $10 Crank and flywheel. $15 Carb and filter, Carb has drilled main jet and 140...

Briggs 5hp I/C dual ball bearing engine.......................parting it out. All sales of any part off this engine will be sent directly to Old timer. Complete motor have all parts available. two small pin holes in bottom of tank. everything else worked. Who needs what and what are you...

Yet again I have FAR too many gas tanks and need to sell some off. Buyer pays actual shipping! Rectangular Tank. Roughly 10" long, 4" tall and about 3.5" width. Clean inside, no gas cap. - $15 Small Square Orange Tank. 6"x3.5"x5" Spots of surface rust inside, welded...

Origanal fenders $200 for the pair origanal hanndle bars with clamps $75 origanal forks with intube shocks $375 frame $450 jackshaft $30 wheels with almost brand new carlisle rubber with sprocket tire size 14.5/7.0-6 $150

not familiar with these motors. im missing what looks to be a fuel jet screw of some sort. what part am i missing? do i look to replace this part or entire carb? where can i get this part?

Here is what i have Frame-$100 front wheel and tire(dry rotted)-$50with axle sold rear wheel,tire(good)and sprocket/brake drum-$60with axle sold front fender-$50 sold rear brake assembly-$35 sold kickstand-$35 Add $5 for shipping for each item with the exception of the frame buyer and i will...