spring

I am looking for the throttle linkage spring for the 2.8 HP engine. I cannot find it at my local hardware store. Does anyone know where I can get one?

Spring and spring cups off of a 1971 Cat R4001, will work on other years/models. located in oakley, ca. 94561. $25.00 obo plus shipping.

I have two used Baja MB165's that I'm bringing back to life. One of them looks to have the correct throttle/governer setup and the other has been messed with - missing springs. I called the parts department at Baja who says all their springs are on back order until December. Are these...

TOMAR # 482015 BOUGHT THIS NEW AND DECIDED TO GO WITH 3 DISK AFTER BUILDING ENGINE. RAN ON THE ENGINE STAND FOR A FEW MINUTES SO IT'S NOT TECHNICALLY "NEW" BUT IT IS NEW. 15 TOOTH SPROCKET, BOLT, WASHER, KEY, INSTRUCTIONS, BOX. 3/4" SHAFT ADJUSTABLE STALL PERFECT FOR AN ENGINE MAKING BETWEEN 7...

Does anyone know where I can purchase some spring cups like are used to hold the front end springs? I have a source of springs etc. but I haven't seen anyone selling the cups. I'd appreciate anyone pointing me to a source. Thanks! Eagle

I've been playing with my tav that I bought on e-bay and installed on an Azusa mini bike with clone motor. I'm having trouble getting the tav to engage at a low enough rpm to prevent it from lurching forward abruptly. I also have an older original comet tav on an invader go cart that works...

http://www.youtube.com/watch?v=PKLUOBEerRc&feature=player_detailpage I like the term red republican at 17 min.

So I have an early Manco Thunderbird project with the front end with the springs. I took the bike apart and had it sandblasted. I put the front end back together and noticed 1 side is like 5/8" longer than the other. The longer side is as if it needs to twist more and compress the spring but...

Looking for some help from the Tecumseh "gurus" out there... Is this correct? Please take a look at the photos below. Specifically, what hole in the governor arm that the spring is hooked into. Also, should that spring be under significant tension (as seen in the photo) w/o the engine running...

Need a Heavier tension yellow spring For the driven unit for a tav2-30. Or if any one has an even heavier spring that would be even better. Located in socal.

Anyone have a GX200 governer spring you don't need? On the Greyhound engines it's the black spring. Thanks

I need a carb kit for my 8 hp Tecumseh on my super bronc. I also need the return spring for the throttle, any good sources? I also do not have my model number handy, so I am not sure the exact parts I need. Any help is greatly appreciated. Thanks.

hi the part @ is 14751-883-000 SPRING honda. is this a 18 lb or a regular spring?

DJ-1001 Dupor 196cc OHV Racing Engine hi i will be changing the springs to 18 lb. do i need to buy shims? if so what size .015 .060? billit flywheel instaled

Have a question,rebuilding a 3hp Briggs 80212.I noticed that the exhaust spring has only 7 coils and is much stiffer then the intake spring ,which has 8 coils.You can basically squeeze the intake side together and also,the bottom 4 coils on the intake side bunch up at the bottom of the...

Have a question,rebuilding a 3hp Briggs 80212.I noticed that the exhaust spring has only 7 coils and is much stiffer then the intake spring ,which has 8 coils.You can basically squeeze the intake side together and also,the bottom 4 coils on the intake side bunch up at the bottom of the...

Can someone post a picture of the spring and location of the spring that attaches to the muffler cage and throttle linkage. The heat cage broke off the muffler; i found the cage ... But Lost the spring. Does it hook to the linkage side with one hole or the side with two? Would like...

I have been going through a bunch of stuff that I have accumulated over the years and know there is someone out there that could really uses some of this stuff!! If your interested PM me with the ITEM # ITEM # 09 & 10 Bonanza Fenders no pitting no dings or dents.. $45.00 each plus shipping or...

Old huffy minibike roller sitting in cambridge NY near albaney needs ride to carlisle pa spring car collectors car show,or near by plus or minus miles, the show is this coming this week4-26-5-1, would like to spend around $50. eny help would be great,thanks you all,wayne.

Hi All, well a couple of days ago it finally warmed up enough to get the VT-7 out for the first ride of 2011 and since the resto last winter. It ran great and drives good, its going to be a fun summer:thumbsup:. Well maybe we just got another 4" of snow Friday night:shrug: :no: