steel

I have looked!!!! What do most people use? The frame!

1953 Cycle Scoot in any condition, and 6" steel wheels.

asking $50 located in so cal.

:rolleyes: Made in China,they fit most of the replaceable ones that pivot like on the early birds,Sears,etc. $15 shipped gets you both. regards,Joel

These fit the previous 4 brake drum/3 brake assy that I just posted. These have some stain/corrosion on them,but they are NOS and I believe they are cad plated(or zinc). $40 shipped to you via UPS. regards,Joel

I have 2 6inch one piece steel wheels, tires are shot but the rims are solid not dents or bends, very minor serface rust. These wheels came off a go-kart and the bearings are 1 3/8 od 3/4 id but as you can see from the pics ( yes EZ there are pics :thumbsup:) a standard mini bike bearing with a...

Got 4 of 'em,dimensions are on the one fender,will ship to the lower 48 for $10 Must have a physical address......I ship UPS only.\These fit the 5" and 6" wheels.

Mechanicsburg, PA $55.00 Including Shipping 8.5 X 4.25 Fill and outlet both on end. Has rust spots inside. Run this petcock OldMiniBikes.com - Discount & Replacement Mini Bike Parts and it wouldbe fine. Will need a new gasket made for under fill cap. I need to hold firm on the $55.

New in box only bolted up never run cover is very nice and has only very minimal scratching from handling, comes with 20tooth 41 pitch sprocket only, use your clutch and get some sprockets and you're on your way! Will work better on a clone or tec. powersport as the briggs tanks cause you to...

kenda tire, the crappy black paint washes off with a little laquer thinner... $20 plus ship

Need 6" X 3 1/4" steel wheels, 'smoothie' front and drive rear with sprocket.

The top half and front bumper of this kart are stainless steel. I had another made ENTIRELY from stainless steel drag links axles and all.. This has to have been made by the same person as the first one I owned. Both were bought three years apart in two different junkyards 25 miles from each...

1 5/8" center hole 4- 5/16" bolt holes on 2 5/8" bolt circle 60-70 teeth Let me know what you've got... thanks!

As the title says - looking for a one piece steel 6" rear steel wheel with a 60 tooth sprocket. (it is for an Arco EZ rider) Must be straight and in very good condition (including the sprocket). The paint is no concern. Contact me via PM. Thanks in advance !

YouTube - Briggs & Stratton 5HP Billet Steel Crankshaft from Eagle Specialty Products ID6671

pm me, ca $60

Here is my new tank. Its Polished 4" round Stainless Steel, 12" long and holds 5/8 of a gallon. But it could be aluminum or steel. Fits nice under the frame. Couple of dryer vent worm clamps (hose clamps) to hold it on. Brass fittings from Home depot. Builder is ummmm its up to him if he wants...

We need a new bike for this year but I do not have 300-400 hours to put into a project right now. I really wanted to build a street legal mini Servi-Car with a titled X-90 that we have in our shop but it will have to wait. I just can not dedicate enough time to fabricate the fiberglass fenders...

looking for sears steel 6" wheels and sprocket. thanks steve

Hey guys,I am selling my 6.5 intek motor, It came off a pressure that my uncle had bought used a few times and then sold off his stuff do to money problems, I had to take off the pump part, and change the oil and plug,I started it up and it sound stronger than ,my built clone LOL. any way I have...