WTB: Tecumseh gas tanks and brackets:
H40 White plastic Red cap center with bracket.
H40 Black plastic Red cap center with bracket
H35 Bolt On muffler 8" Black/ original finish
Thanks.
Trying to get a feel for whether or not to replace head bolts. NOS Tec H50. Had to remove tank bracket and plate around spark plug to clean-up some paint damage from sitting around for 35 years. Going in with a new gasket but wondering about bolt stretch... Opinions?
I'm looking for a Briggs side cover for a mid 60's 4hp Briggs. I believe a 5hp cover will work too. I need the one with the 4 bolt holes in the square pattern around the shaft to mount a taco clutch guard. Thanks, Chad
Okay I know I'm not going crazy and there used to be a diagram for this. Can anyone give me the measurement 4 hole to hole on a predator, for where u bolt a clutch guard thanks guys
Putting a new main crank bearing (ball) in my rebuild project. I see in the Tec manual a mention of a retaining bolt on the inside of the case cover. When I tore it apart, I noticed there was none installed. I see two holes that look like they could be used for this. Do some people NOT put these...
I bought a set of 6" wheels and tires at a swap meet, wheels and tires are in good shape. The problem is, they have a 5 bolt pattern. Anyone know of a #35 chain sprocket with 5 holes instead of 4, or will I have to get a new set of rims.
Hey there everyone,I havn`t on here in a bit working alot,well here it is I just purchased an 8hp(301) preditor motor.I`m putting it in a baja warrior,I was wondering what are the best bolt on mods i can put on,and what is the best tc on can put on it?
2 guy are duking it out for a Bonzans fork bolt $42 Fork Bolt Original Bonanza Mini Bike BC1200 | eBay when I took the one out of my bc1300 the lower neck bushing had nice threads in it you could move the forks around about 2-3 " I put new bushing in it and got a new bolt that was longer and...
just wanted to post some pictures of my thunder bolt with a modified clone engine on it and yes for you vintage flathead guys. this will go back to stock in the future when i decide to do a full restore...:thumbsup: but for now going have little fun with it.....:scooter:
thanks again for some...
Hello all,
I am finishing a restoration on an Alsport Tri-Sport RTS-SL and I need to drop the diff and replace a broken diff bolt and sprocket mounting nut but I want to buy averything ahead of time. So I was wondering if someone could tell me what size, length and thread diff case bolt and...
The wheel I am using has the 6 hole 3.25" inch bolt pattern and I am wanting to find a drum brake assembly that has the sprocket built in. If anyone has done this setup, please let me know. I am looking for the parts but many of the sites that sell combo brake drum and sprocket does not...
On my Cat 400X the pipe where the steering bolt goes thru is worn out causing the bars and wheel to go fore and aft. I took it all apart and did not see any bushing. Is there a replaceable bushing or what can be done to fix my issue ?
Alright so I bought black 10 inch rims from ombw thinking the bolt pattern would be the same as the chrome 10 inch rims, turns out they're not the same, anyone have a way of making a pattern or something of that nature to save me the hassle of shipping them back?? Anyone have any tips On how to...
I bought a NOS Pulsa Jet carb on ebay and a fuel tank for my mower. Got it all together and found out the choke linkage cover bolt hole is not threaded , its not stripped out, just was never taped at the factory. Would anyone know what type of thread this would be. Probably will end up taking to...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.