broke

Hi everyone, got a problem, i have a tecumseh H50 motorsport crankshaft. its the 1 inch rod journal. well i managed to snap off the fly wheel nut. my thought is to take it to a machine shop and have the flywheel side drilled and tapped at 1/2 inch 20 . a stud would be placed in the crank with...

I recently put a new cam and 1.3 ratio rockers on my predator 212cc motor. The compression release works and the valves are adjusted right. It starts after two or three pulls, but sometimes it yanks the cord out of my hand so hard its kinda scary.

So I dug out my Db 30 + 196cc that I hadn't ridden in a year or so, but it had sat out in the weather that whole time. I cleaned the carb as best I could, and put it back together. I could get it to run for a few seconds but it would putter out. Figured just need to adjust the carb, so I found...

My Clutch teeth last a week tops,broke all the time with the #35 chain so upgraded to #40 chain and sprocket setup.still the clutch sprocket teeth all break off.tried Hilliard Extreme Duty and Max Torque clutches both very violent on takeoff and broke teeth off and even broke frame welds...

what you see is what u get, I bought it with some other mini stuff at auction, has compression, side cover broke 100 OBO TRADE PLUS SHIPPING

Hello, i got into this not too long ago, bought a 1971 Kawasaki kv75 from a local junkyard, then had to sell when my truck broke down. Currently i have an old minibike frame i got from my cousin. Im guessing its a Bonanza. I have a tecumseh h30 that is going on it.

Went to put some stuff away tonight and i think a cable came undone in my mini bike shed.....going to be a long week cuz i cant get my babies out! Hope this weekend i can try to figure out how to get the damn door open great start to the week lol

I installed my valve springs today and it got super hard to pull start and my pull start broke after like 50 pulls and my engine wouldn't start so Idk if it's the pull start or something else (worked for 45min straight prior to gas runing out then I filled it up and that's when it wouldn't...

Lol i broke my left forearm during wrestling practice.. now i have to wait to finish my progects:doah::doah:

as stated,front chain tensioner broke off & was chewed up, threw the front chain. it was suggested to use a skate board wheel{great idea} my question is, can i mount it solid, or does it need to "float" with the chain to keep tension on it to keep the slack out???sorry no pictures. thanks in...

i need a hydralic brake lever. i dont want to spend $42.00 on a whole new setup. where can i find parts? it was made of the cheapest chinese metal:censure::censure:there goes our sunday.

PLEASE HELP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! HI EVERYONE I GOT ANOTHER PROBLEM MY CLUTCH IS SHOT!!!! All i have is another clutch that is 10t chain drive, well the only other gears i have for my jackshaft would be 12t in 12t out, 60t final axle. well that didnt works so well gearing must...

Wussup guys my crank bolt broke off into my crank one day when I was trying to remove or tighten the flywheel(didn't know about the rope in the sparkplug hole trick yet)..I used a maxtorque clutch tightening it by the allen bolts but I just got a premier titan clutch(blue springs) and I realized...

Yep i did it again. As some of you may know i broke my left collarbone exactly a month ago. Well it broke the same one again. I was out on the dirt bike herding sheep and one broke off from the group and went down into a dry creek bed. So i got off the bike and went down into the creek to get...

Just a heads up to super Bronc guys I was riding my super bronc last weekend doing wheelies, little hops and some fast trail riding when I was putting away my bike I noticed a 6" crack along the motor plate weld where it attaches to the frame. Keep an eye on them. This is the first one...

CLEAN MINI BIKE- L@@k!

i over tightened the bowl and the metal snapped. :hammer::scared:

How do i remove the jack shaft for the driven pully of the torque conveter.I have the assembly of the trike but the shaft wont come out of the driven pully,Cant use a puller.cause you run the risk of messing up the pully.Please help, any ideas.

Today I traded my 1981 Goldwing that was not running, for a Vespa Piaggio Grande. Not a Mini Bike, but I am sure I will be forgiven on this one. I think it is real cool, and if anybody has any parts for them let me know. PS you can see my 40 dollar Ford LGT100 lawn tractor find in the pic.

well i got a new brake from the internet . it took a month to get here and it doesn't fit. it is smaller and the hex screws thread into a tapped spacer /?? WTF? after an hour it fabricate and bend the frame holder it wont stop the Bug. so I put the old one back on and the top cast broke. i...