driver

Selling my Tecumseh HS50 that I bought a couple months ago. I was going to use this on my Gilson project but decided to go ahead and get the more correct H50 engine. It came off a lawn mulcher and ran great when I took the mulcher apart. The only thing missing is the gas tank and tank mounting...

looking for a max torque 2 speed clutch, driver needed.

So I thought I got all of the bearing out of these wheels by hammering lightly with a long screw driver from the other side. But did I leave an outer casing there or something? And I can't get to it from the other side cuz there is a rise or like a ledge behind it. OR is this part of a very...

I actually just need the inner flange if anyone has one. The one on my Roadster is worn all the way through the face. I'm not in a hurry, but I'll need it soon.

Inventory of New Old Stock made in USA Comet TAV 2-30 Torque-A Verters drive parts and covers I have complete units, drivers, sprockets, driver springs, drive belts, driver buttons, black plastic covers, etc. Units are available for use with #35 and #40/41 chains and drivers available for...

I just feel like the driver isn't grabbing enough shaft. After all the spacers are put on, the driver is really only grabbing like maybe 3/8" of the key way. It just seems like that is way too little. Anyone have any insight?

looking for a new or like new Max Torque tav driver...

Comet Tav30 new mounting plate (metal style) new cover new #41 pitch 10 tooth gear new shaft/bearings new driven clutch good used driver good used belt all Comet parts $100 plus shipping Pics to come

Does anyone know the thickness the driver spacer needs to be to put the TAV2 on a Predator 212? I don't have the spacer that came with the TAV2.

I have a tav2 that was going to go on a different project, but that was 1" shaft. I just got a predator 212 hence the 3/4" need. I'd be willing to trade the 1" or buy the 3/4" outright.

No matter where I set tension, there is enough friction on the driver sheaves to run the driven. I set the driver up loose which widened the sheave gap, and it works better. Do I need a wider bushing or spacer to get more distance between the sheaves? This happened rather suddenly on a...

I started breaking down my MTD today and can't seem to get the driver off the shaft. I was able to take the outside of the clutch apart, but the last piece is stuck good. I soaked the shaft with PB blaster and let it sit. I don't want to put a puller on it because the pulley already had a...

If you have one to spare, let me know and how much please? I have trades as well. Thanks!

Does welding the sloppy clutch bell to the driver improve the clutch shudder and vibration? :shrug: Lifan 2.8 power.

looking for a deepco driver and driven. 3/4" driver 5/8" driven, 6" or 7" driven

This is the bushing that goes between the driver halves and the belt floats on it at idle I assume.

*DRIVEN* In good shape needs the retaining clip to hold it together. Was fuctioning fine until that clip broke...40 plus shipping located in cedar falls Iowa

looking for a new or nearly new max torque tav driver 3/4"

Hi I'm gathering up parts ready to restore my Harrison wildcat. I need a salsbury 330 or comet 340 driver (I believe they are the same thing? ) or maybe a modern made equivalent if there is such a thing that will run with my 330 driven. any help would be great. only snag is I would need it...

I ordered a replacement TC Driver for my 71 Rupp Roadster/2 from ruppparts.com. Rupp Blackwidow, Roadster 2, Scrambler, Enduro TC-1 torque converter What they sent me is in the first picture. Does anyone know the order that it all goes together? It included (2) 3/4" washers and I don't know...