h35

Head & Bolts. Hot tanked, with 3 New head gaskets Flat, no cracks, but has very small chip on one fin. Gas tank, with top bracket. a little beat up, but No leaks. Sidecover and Bolts. Cam, and tappets. But wait, there's more! A brand spanking new #35 master chain link. $60...

Need a Tecumseh H35 fuel tank for my early 1970's model Huffy Hustler rebuild. No black plastic tanks please, trying to keep bike original as possible. Send me a pic if possible of what you got. Thanks for looking!

I am putting an H35 together after having received it disassembled. Mounting the ignition assembly (which is in one piece) looks straight forward but the plug wire seems to get compressed a good bit as the two bolts holding the assembly are tightened against the block. I see where I think...

Hello everybody, I figured I'd move this question here where it belongs. See photos of my H35, I am missing some parts, I have no idea what the exact model numbers are because I am missing the engine shroud which kinda stinks cause I can't just look it up on tecumseh parts site. There are a few...

Tecumseh H35 shortblock professionally rebuilt. this is a points and condensor block. Factory parts used throughout. Fresh .020 over bore, nos piston kit, rod and crankshaft. new gov shaft, crank seals, in valve, exhaust guide, recut seats, decked .025". ready to go. head, valve cover and intake...

I am in LOVE with this muffler! (LOL!) Tecumseh Motor H35 Original Vintage Rupp Bananza Mini Bike 3 5 HP Running Engine | eBay Doc

looking for a H35 piston kit 34515 +.010 or piston 32548B ringset 28987

I am at my usual loss. While,removing the wrist pin on my Rupp engine the spring, wire, deal that holds the wrist pin in the piston went flying in the yard somewhere when I removed it. My question, do I need a H35 specific wire retainer specific to the H35 or are they all the same? Anyone...

I have a h35 that seems to run out of pulling power once it reaches like 10-15mph. It feels like it just dies and then once speed comes down it has power again. Can't seem to keep it pulling. Any ideas? Thanks

A little beat up, came off a hardly used edger, strong compression and "Ouch" tested spark. Weird that it has the mini bike correct gas tank and air filter. Looks like a 5/8 shaft? Definitely gonna need a carb cleaning or rebuild from sitting, I will pull the edger pulley off if requested...

H25 side popper $100 plus shipping H35 side popper $100 plus shipping I also like cat parts

oh man i really screwed up. i need an H35 head. if you have a spare head or engine contact me asap!

I pulled the old clutch off of the tecumseh h35 engine using a gear puller. Purchased a new clutch only to find there is no way to retain the clutch on the output shaft. No snap ring groove, set screw hole, or threaded hole in the end of the crankshaft. Can someone tell me how the clutch is...

What is the difference between a hs35 and h35. I have a rupp scrambler with an hs35 and I'm looking for a block. So curious what I got to search for?

I pulled the engine off my Trail Bronc VT-5 and it is a 3.5HP Tecumseh engine with the clutch. I still have the sticker with the model number (which says H35) and such. How can I found out what year this engine was made in? I'm going to try to clean this engine up, get it running and repaint it...

Im.looking.for a white good condition sn good running 1970 tecumseh h35 side popper shipped to 32765 can text me at 407-393-8835 thanks...

Looking for a Taylor spark arrestor pipe and muffler for my H35. A chromed one would be nice! Thanks in advance! Jason

Would a Predator 6.5hp from Harbor Freight work on this old Manco Crusier torque convertor setup?The Tecumseh H35 on it needs work and I want to see how this bike rides and maybe rebuild the H35 and put it back on later.I see a post with a predator on a mini like this one and don't have a...

Anyone want to sell me a decent running 1970-75 h35? Doing a modern/vintage restore on an arco ez rider for the wife for a parade bike. In the "gathering parts" stage. Got everything but a nice engine. I dont wanna strap a clone on it. She isnt ready for it :laugh:.

Hey all, I have decided to rebuild my H35. It has terrible shaft play, and it's had a rough life. :doah: I am fairly sure I have the lighting coil? It would be cool for sure! It says magneto on the small cover. I will post a picture of the numbers. I think its a 1964 motor. any info on...