pics

Mini Bike & Go-Kart Parts

  1. MTD ENGINE CLUTCH COVER BRACKET 5

    MTD ENGINE CLUTCH COVER BRACKET 5

  2. MTD ENGINE CLUTCH COVER BRACKET 4

    MTD ENGINE CLUTCH COVER BRACKET 4

  3. MTD ENGINE CLUTCH COVER BRACKET 3

    MTD ENGINE CLUTCH COVER BRACKET 3

  4. MTD ENGINE CLUTCH COVER BRACKET 2

    MTD ENGINE CLUTCH COVER BRACKET 2

  5. MTD ENGINE CLUTCH COVER BRACKET 1

    MTD ENGINE CLUTCH COVER BRACKET 1

  6. IMG_05232

    IMG_05232

  7. IMG_00944

    IMG_00944

  8. IMG_00933

    IMG_00933

  9. Sixpac440

    Induction heater to remove a stuck pully .... SWEET!! Pics (of course!)

    I have an early 80s 30" cut rider mower that I have owned since 1998. I have had to rebuild the transmission (Forward, Neutral & Reverse only), The Transaxle, front end joints/replaced the axle assembly, made a seat ... well you get the idea .. I really like this little goober ... New...
  10. Sixpac440

    Fixed bikes ... pics and a plug!! Dorothy is still on simmer ...

    My Dorothy project has been on simmer while other projects have taken precedence. jeep4me needed some struts made for this bonanza ... also at some point in it's life someone hacksawed the fork lowers off because everything was frozen ... Some PB Blaster, a torch, some 1/2" dowels and a lot...
  11. IMG_23911

    IMG_23911

  12. IMG_2390

    IMG_2390

  13. Sixpac440

    Tec H50 with Oval Bore Mikuni problem ... pics and Videos ...

    I have a NOS Tecumseh H50 motorsports engine and I put a Mikuni 22mm oval bore on it. It gets to 6500 rpm and stutters .. if the throttle is cracked wide open it bogs down. I have played with the stock jet by drilling it open and adjusting the clip on the pin. I have tried it with and...
  14. cambo61

    FS Burnishing for minibike parts (pics)

    Folks. I've been a forum member since 2010 and have been involved in vintage karting since 2002. About 3 years ago I bought an ALMCO V3 to help the community with restoration or modification of surface finishes. I own 2 minibikes, my prized 1947 Cushman, as well as 10 vintage karts...
  15. Sixpac440

    I have an H70 with scoring and it had a stuck pushrod ... Pics ...

    Looking for some input .. is it worth fixing? It had a stuck open exhaust valve due to a stuck pushrod .. Possibly tied in with the breather being plugged with mud .. The piston is scored both front and back ... The cylinder is also scored up front and back .. I...
  16. Sixpac440

    Just got home with a Heald VT-7 .. Pics ...

    It died on the trail in 2003 and has been sitting in the shed ever since, 14 years. Tires hold air but are weather checked. The gas tank is bone dry. plug was covered with soot. I pull the ripcord and it dosent feel like there is compression .. I don't see any holes in the block. Oil...
  17. OND

    Can't Post Any of My Pics

    For some reason when I go to my pics or anybody's pics for that matter there's no URL's or No MEDIUM or anything else. Any body else having this trouble or is it just me ?:shrug:
  18. U

    CCS Charger pics and questions

    Snagged this so so survivor today off craigslist.i didn't know what it was other than old ( because I am) and got answered in " what is it thread" in minutes. Not sure but the Tec engine tag is telling me that it's 1971 ?? Can anyone tell me what the 12 S stamp on the frame means? I had zero...
  19. IJG

    Pics of Willwood Brake Calipers on their minibikes?

    A Friend & I are interested in upgrading parts ' Anyone install a Willwood brake caliper setup on their (minibike)? Bolt right on, or did you need a special brackets? show pics please Both front & back would be sweet.
  20. SIDEPOCKET

    Recap and Pics from final LOMBRA race of the season!

    So I'm a little bit late in posting this up, but I am a world class procrastination champion :laugh: Our last race of the season is supposed to end up some time in October or November (or before the snow hits). But due to scheduling conflicts, and me only being home for 28 days at a time, or...
Top