tav

I have a Tecumseh H50 Motorsports engine with a 3/4" shaft that in stock configuration should make about 9hp and 7000 RPM. I may tweak a HP up a bit in the future. Question is are there any TAV setups that would work at that RPM and handle the HP? I found this...

Hi there. Has anyone replaced their MTD/Columbia original V Plex Tav driver and driven pulleys with Comet 30 series components? My original V Plex driver is shot and the driven one has the jackshaft seized in place :( How did these original units perform compared to a Comet piece? Thanks

Had my first follow-up with surgeon today (he's pleased, so I'm pleased), but before I headed to Winchester I finished up a pair of TAV Jackshaft Brackets to install on Copperhead, my "mule" bike. The difference between these brackets is the TAV bearing mount is welded to rather than bolted to...

hey guys i have a baja warrior with a tav2, that thing got alot more torque, on take off it pull the front wheel off the ground, my question is i got a 50 tooth rear sprocket, how will my performance be if i went with a smaller rear sprocket? and what size is recommended, and where to order...

Any one have some good covers or know of repops?

I am building a 212 Predator hemi with all the goodies just short of needing machine work to go any further. The engine started out with 6.5 HP before I added anything to it. 30 TAV's claim they are good to 8 HP. Should I go with a larger TAV and bush the crank to fit, or am I drinkin my bathwater?

Guys, I apologize for asking something I'm certain has been asked before. I swear on my only child's life that I did a search, and there is a lot of info our there on this, but I was having a hard time finding what I'm after. I need advice on what gearing ratio I should shoot for wit my tav...

Sold the bike as a roller so I'm not needing this anymore. Go Powersports 40 series bolt on kit. Backplate belt 3 sprockets 10,12,14 420 chain Driven pulley Custom abs belt cover and mount Will come with some random setup stuff for a 44c also Needs a new 40 series driver $200 shipped...

Here we have a powerful little mini bike. She uses the Tecumseh 5hp Power Sport engine and is backed up with the Comet TAV. Think of a heavy duty built Miniature Baja Heat but with rigid forks. Starts easy, pulls like a Mule and stops well. Kill switch works. Just installed brand new recoil...

Could really use some help figuring out how to get this kart rolling well. We've tried a couple different belt lengths, but the belts were V-shaped (symmetrical) and didn't move the driver clutch well. The set up is a Comet 30 clutch with a Max Torque pulley clutch. I don't know if this...

NOTE *I made my own jackshaft a while back to replace the worn one so this isn't 100% accurate to a stock jackshaft install. * The driven and Driver are 30 Series Chinese, the belt is genuine Comet #203590A While I had the shaft out I put 1/4-20 tapped holes on the ends of the shaft ... I...

There are 3 holes the spring can go in ... I want Hill Climbing/Trail Riding power ... Where should the spring be ...

Hi ..I live in upper Florida and the ground is really just sand..in my case would sand score my driver pulleys to death using a tav? any input appreciated.. thanks

I'm looking for a good used hard plastic torque converter cover. Needs to be usable, with no cracks and the slots intact. I can get a new one for around $35, but would prefer an experience one for a survivor bike I have. Thanks!

Well I have a new generic TAV. It came with the driven pulley locknut (nylock) loose. Is this an adjustment or should I simply torque it to a certain spec. Or just go ahead and tighten it? Sorry for the newbie question but I did search and came up short. Three letter words like "nut" and "TAV"...

So, I'm thinking about a tav for my fat bike, I guess I really should have designed it around one... My homemade setup uses a 3/4" jack shaft and a 1/4" plate. There's about 2 1/4" between the jack shaft sprockets. I'm thinking I could almost make a tav and backplate work if the sprocket was...

we are finally getting around to the boonies,and ran into an unexpected snag. with the tecumsehs,the tav is straight no problem,but with a predator motor,the tav plate is angled into the engine tray..? has anyone mounted a tav on their boonie bike and if so,how did they do it? and i saw a...

we were looking at the newer tavs and the differences,and wondered this. we do have a bunch of older comet tavs laying around, most were for go carts so no backing plates,but we have all the pieces. we were thinking about having a couple of plates machined up made out of steel instead, and then...

these el cheapo tav 2 sets on ebay,are they any good? i have sorted thru a ton of websites all selling tavs for different prices and they alllllll look the same.?? heres an example. Go Kart Torque Converter Kit CVT Clutch 1" Comet TAV 30 219554A Manco 12T 35 | eBay Go Kart Torque Converter...

How can i tell what chain size this Tav uses? Help