block

Sears/ Tecumseh big block, came off a snowblower still has the snowblower clutch, running condition, 75.00 picked up in Midland MI or I can bring it to the Ann arbor show.

Is this H70 shirt block a points type or an electronic type ignition? Or can it be either?

just wanted to make sure that a genuine gx160 would actually have that stamped on the block... where if the block is stamped gx120... its obviously a gx120 with a gx160 recoil assembly on it? have a motor sitting, was going to put it up for sale and just fired it up for the first time (since...

440cc Clone Engine Kits - Generation 2 [G2440] - $399.99 : Vegas Carts & Performance, Repowering Golf Carts for todays Speed Freaks! Is anyone running on of these? I think I found my rosebud.

So the piston rod decided it didnt like me and the piston came apart. The block has some groves cut in it now pretty bad.. Question is do i get a new block or have this one honed? Or can they be re-sleeved.. I don’t know much about this I’m learning as i go..

NOS big block throttle parts. $60 shipped...Paypal only - located in WI

Here is a bike I got from Randy at Windber last year. H60 with a comet Tav. I bought a set of forks from Guardrail Dave for the front but were to nice to use.I kept it like a rat bike for now. Used a pair of KKK forks he had from the spitler project. They look right at home on it.This bike is...

A couple pics of my lil Indian with a hot rodded 11hp TEC big block , nice fit with torque converter and jack shaft . Crazy bottom end and geared for 60 + mph :scooter::scooter::thumbsup:

5000 with big block TEC motor

Honda gx200 3" block braced with deck ecstension $200

I need a good block for k91 mine is trashed and already 30 over plus 30 over bore rings cost a lot more I have a Tecumseh h60 I will throw in for a block

Got this blower housing in a bulk buy of Rupp junk tonight. It's a 1970 H50. It even has minibike throttle linkage!

Looking for an unmolested block in good shape. Will take a short block or motor, but already have parts to rebuild a bare block. Prefer iron bore, of course, but willing to take a good used Koolbore if original bore. Thanks!

Cleaning out some stuff, all this stuff is from H series period correct year engines. Crankshaft, 1971 H50 ball bearing supported, 3/4" tapped shaft $30 camshaft 1971 H50 with lifters $30 ball bearing supported sidecovers $10 each (2) heads $5 each (3) 1969 HH40 stamped plate engine...

If I had some of the 30199 made up would anyone be interested? IF so How much would you be willing to pay?

Plays well with others :laugh:

The big block covers without a bump are getting a little harder to find in good shape sooooo....... I have a nice solid cover with a bump and a not so solid cover without the bump... The donor cover was all rusted out on the bottom more than likely from sitting in the dirt or some old damp...

The big block covers without a bump are getting a little harder to find in good shape sooooo....... I have a nice solid cover with a bump and a not so solid cover without the bump... The donor cover was all rusted out on the bottom more than likely from sitting in the dirt or some old damp...

Throttle linkage Tec h50, h60, h70

Parted out new predator for head and some other things. For sale is block, crank, side cover, flywheel, rod and flat top piston. 60$ plus shipping. located at 10509. Will consider flat top and rod for 30$ plus shipping. Flat top and rod will fit all predators. Block is honda clone style and...