block

Hey guys, i want to paint my gx200 block and i want to use duplicolor satin black engine enamel on the actual block and Dupli-Color Metalcast Aerosol Paint Enamel, Orange Anodised, 311g for my head. should these hold up against the motor heat of the motor? they are both rated to 500 degrees...

Looking for a block for a tecumseh hs35. Thanks

What is the difference between a hs35 and h35. I have a rupp scrambler with an hs35 and I'm looking for a block. So curious what I got to search for?

Anybody on here who can do all the machine work for this? Or can somebody point me in the right direction for it? I'm looking to get a resleeved block and milled piston.

I have a Genuine Honda GX200 and I would like to do a 3in build. can someone tell me what are some of the challenges I will have with the build as far as having it resleeved? like when you resleeve the block do you have to leave the sleeve raised above the block and cut the head to except the...

Can a BZ3 block be taken out to 3.5" bore? I keep reading conflicting things. Also does anyone have pics of where these blocks get welded for strength? Any shortcomings of this block that I should know about? Will this block take 50hp? Any recommendations on brand as far as side covers or...

Anyone have or seen any photos of how the lighting coil (I would guess the proper term would be "generator" but I dont want to confuse it...its for 12v output for a starter usually) setup mounts underneath the flywheel? Seem like they are usually found on the Military engines. trying to...

So today I was riding my trike on a field. While riding slowly back to the car it suddenly stopped. After inspecting the engine I saw a huge crack on the block. Anybody got any ideas on why this happened? Modifications I've done. Milled head 0.080. Ported and polished head. Flat top...

Tecumseh h50 lighting coil block has block,head,piston,rod,lifters,and cam . i am never going to do anything with it so $20 plus shipping :thumbsup:

How do I change the oil seal on the side of the block where the crank sticks through? the bearing is good so id rather not mess with it, but the seal is bad. got a new one ready to go. the block is all tore down.

The last gen HS40's they swapped the intake and exhaust so it looks just like an H35. Anyone know if at that point did they just up the HP on the smaller 3.5 block somehow or was it still a physically larger engine block :shrug: Also did they still have mount points in the casting under the...

So I have 2 motors with similar builds... 32/28 valves ported, 310 cam, billet flywheel, 40 though longer rod,flat top piston, billet lifters, hl380 tilly on alchohol, 1.3 roller rockers. Here's the question, One motor started as hemi, the other non. Would the hemi block one need 5.440...

Looking for a crankshaft for a Predator 301cc engine. Anybody have one? Even a damaged short block may do if the price is right.

I've made no secret I'm a drummer and drums are my other great passion in life. They also add paltry sums to my income. Mainly though I've been lucky to accumulate some fine instruments over the years. In my "Drum Machined" post a few months ago I showcased my Trick Drums, a modern state of the...

when I get some space cleared I want to work on the original 4hp for my 1967 Fox campus. It supposedly runs and all that good stuff but I never tried to fire it up. when I was cleaning the gunk off the engine I did notice that the mount lugs for the coil are not the same as a later...

I don't know where all these things come from...the good folks in China must have a factory where they turn these things out 24/7. :doah: How could so many different sellers be making money on these things ?! Seriously...how many people named "Fred" or "Edna" are currently in the market for a...

Need two of part 30199A for H60 motors im trying to put into service. This is the speed bracket recommended in the Tecumseh section on hooking up big block throttles. I found all other parts for this hook up. This part is nowhere I can find..

Hi I'm looking for a Briggs cast iron sleeve 3.5 I got stuff to trade. I only need the block. Thank you.

Briggs 5 hp flattie Model: 135212 Type: 0130-01 Code: 94120507 Parts: Block -$20 rookie honed and gov removed Head -$15 Has carbon Crankshaft- $20 Cam- $15 Blower housing- $10 Side cover- $10 Tank $15 small pin holes in main jet reservoir, did patch with some steel epoxy...

Vintage Briggs Amp Stratton 131432 5HP Side Shaft Engine Block | eBay