bolt

Blasted, sanded primed and painted, assembled my Hornet frame. Gently tightened down the bolts that go through the fork to hold the top of the front suspension springs inside the fork and.... paint cracked and chipped around the bolt.Was thinking of getting small piece of maybe 1 1/8th tubing...

Does anyone know the exact bolt pattern for the Arctic Cat 6" wheels? Im specifically wondering about the 3 bolts that hold the brake drum on. Thanks in advance!

what are these holes for ,they dont line up, unless i measured wrong

Hello Fellow Minibike Enthusiast's & Motor Head's. Today I acquired a Motor, Clutch, Some kinda jack shaft pulley system, 2 #41? Chains for the jack shaft & Rear wheel & Throttle Cable' All from a Old Time Friend. I believe it may of been from a Baja MB 200. (Not Certain) :shrug: Can Anyone...

OldMiniBikes warehouse is shipping my air filter kit without the carb stud because they are out of them. I was told I could use the stock stud just back it out a little..is this true?

This wont last long....Maybe someone here needs one? Vintage Kart Mini Bike A West Bend 510 580 700 Die Cast Exhaust Header | eBay

I took my carb apart on my Baja DB30 for a thorough cleaning and lost the hex flange bolt that holds the cup to the carb. Can anybody give me a part number or size so I can go to the store and get a replacement? With the seal. Same as in pic next to drain screw. Thanks [/URL][/IMG]

Can someone tell what size of a bolt and is it fine or course thread that goes into the side of a 3.5 hp Tecumseh to hold the bracket for a band brake thanks

I need to know what size bolt goes in the end of the shaft that holds the clutch on. It's a red 4hp. Honda. thanks joe I think it's a Honda GX120-TX2 5/8

I'm trying to figure something out, I want to do a bike with a torque converter assy thats just a standard clutch/chain hardtail frame. I don't want to alter the frame though. I saw one similar frame to the one I want use had a big block Tec with comet TC and it looked like alignment was...

Where can I find a bolt in this size and fully threaded? Looking for a 4" fully threaded 5/16 bolt. Preferably a 3 1/2 Allen head or a 4" hex head will work too.

I can loosen the one on right but not the one going thru exhuast! Tried liquid wrench ,wd40 etc.... Just can't get it to move? I don't want to strip it!

OK Has anyone ever heard of a clutch bolt on a 6.5 horse clone motor coming loose when you turn engine off? if so how do you fix this problem????

Dudes Went to tighten down the exhaust pipe on my 6.5 Clone. It's got studs that screw into the block, and then nuts screw onto the studs. WELL....i went to tighten the nut onto the stud, and stripped the threads on the stud?? :cursing: Anyone know what size bolt/thread and pitch the...

just like it says, i am sure i can find one like the ones on a baja warrior but i need it to be for 35 size chain? Or if the sprockets are interchangeable? i will consider what you got?

My motor build is going to be done soon and with it going to be all nice and new looking. I was thinking of replacing all the bolts with some nice stainless. Does anyone have a list or link of the bolt sizes used on a 3 Hp Briggs or dare I ask is there a bolt set available somewhere?

I know its a long shot but even a toasty one to copy will do...:mad2:

I stripped a arc rod bolt on my STD length honda clone billet rod. Hoping someone has an extra one laying around. I'd hate to buy a new set.

Currently in the process of building my Lil Indian small frame and I don't know what size bolt is supposed to go through the front end tube for the forks. I have a 5/8" bolt in there now but it is loose and wobbles. Bushing do not fit to solve this problem.

Can somebody tell me what size bolt goes in here:shrug: I'm sure its Metric:shrug: