case

Hi guys, thanks for any input! I have a Baja Warrior with a 6.5hp Honda clone engine. I took the side crank case cover off the crank side to take a peak inside. I don't have the recoil starter so just turning by hand using the starter pulley is pretty easy. My question is do you have to...

I got this engine in a box with a bike purchase. I was told it runs fine. The PO took it apart with the idea he was going to put a larger piston in it. I guess he ran out of knowledge. :wink: The piston looks good. As does the cylinder. All the small parts are in the small box to the right...

Just picked up whats left of a VT-7, I think. Or is this a VT-8? Older style with only one hole above rear axle bolt for the shock and straight forks. Think I reading somewhere that the VT-7s were blue and the 8s were red but dunno. When I showed it to the wife she called it a VT-zero...

And if not, WHY NOT? (click on the pic to view) Everything is rubber coated so nothing rubs on a hard surface... I actually had to take a bit of the rubber off to get things rotating. We'll see how it looks in a few hours. :scooter:

Well I decided to open up the block that came on my recent find. Some might have read the other post regarding the motor. http://www.oldminibikes.com/forum/tecumseh-engines/77697-a.html Knowing there was new side case nuts on the block I couldn't take it anymore I had to open it up. At...

So i went and pulled my motovox out of storage to try and start it. and it wouldn't start. I put stabil in the gas before i put it away so figured it should start right up after sitting a few months. well i decided to check the oil and gas came pouring out!! I'm guessing it go in through the...

Starting to build a Caterpillar mini bike, Big Chevron Tires, Industrial Equiptment Yellow paint, flapper tip exhaust. 5hp briggs, Gearing down, I need ideas on design, attributes, style and heavy equiptment ideas

Unknown mini bike I picked up today in NJ at swap meet in Englishtown. Another shot from the back where you can see the handlebars attach oddly.

Unknown mini bike I picked up today in NJ at swap meet in Englishtown. Note the crazy handlebars

Looking to buy a Mini bike in a suit case,this was made by Micro Power Products and has a Olhhson & Rice engine on it.Any leads would be greatly appreciated!!!!:thumbsup:

I'm going to look at a Rupp basket case this afternoon. Is there something to look for to determine if it has any particular value or popularity. He says it's a 2.5 hp Briggs that runs and the fork is away being sandblasted. Asking 175 but he'll take an offer. I know nothing about Rupp mini...

Do not mix it.... one of my drivers poured a gallon of dex cool in with the traditional green antifreeze in a new $23000.00 engine... when mixed it will turn the antifreeze to gel.

the features are as follows 1. handlebars and forks are seperate. not too uncommon. 2. a 2 hp briggs that also says 6.65 cu in 3. the jackshaft looks to have clutch that is setup for a clutch brake. im a noob but im not sure if ive seen this setup before. also the bike is about the size of a...

if he still has it in the morning i think im gonna buy it. mini bike parts

At what level of engine build is additional case venting beneficial/ required? Is it just after governor removal or is it related to a specific RPM? My engine is nothing fancy but I do have a side cover leak.

I need the two items mentioned in the subject. Need OEM parts. LMK, thanks.

edit: FOUND ONE! thread is done i need a GX200 case. will do $75+ shipping for one right now. if you have one, PM me. don't post in here because i probably won't see it.

Ok, so I have this nice headlight that I ultimately want to put on my terra torque. It is a nice chrome shell with a push button and toggle switch on the back. Additionally, there is a red wire and blue wire coming out of the shell for wiring up the headlight. I have a lighted H50 with three...

Like the title says, Bird - JC Penny Foremost, wren? may have other names? Frame MUST be this style whatever its called: