choke

Does any one know which tecumseh choke shafts are still available, which have the lever on the right and the positioning spring on the right. The right means facing the carb from the rear(choke) side. I need for both diaphragm and float carbs. I need 8 to 10 for float carbs and 2 to 3 for...

the choke on my carb is loose. i took the carb off the tank and peened it with a hammer and it wont tighten up...any other options?

Hello all. I have a Briggs and Stratton 6.5hp motor. The model is 122432-0113-E8. A while back I had to replace on of the valves and push rod because the valve got rusted in there. Well, I got that all fixed and put back together, but now I notice that the engine idles good when there is...

Hello to all! I have a 3HP BS 80202, built in 1990. After searching thru the forum and making what I thought would be the solution the engine will not start unless I put a shot of gas into the carburetor via the choke. And then it will take a few tugs to start. I replaced the diaphragm...

I have a predator and it starts first pull everytime but when you take the choke off it revs as if it were the throttle. It ran fine before we put it in the frame. Ive taken it apart multiple times and cant find the problem. Any suggestions on where to start looking? All help is appreciated i...

i bought a dbb30 a week ago for $10 it wasent running at all i got it running and the guy i bought it off of lost the drain screw on it. he put a screw on it that was to small and he put teflon tape around it. i took it of and rebuilt the carb and cleaned it out. if i seal around the screw with...

I have a clone with a header, filter, and a #90 jet. It wont run with the choke off and the plug is leading me to believe its running lean. Isn't the #90 jet big enough for the mods? :confused:

posted a video here 1333317656.mp4 video by iatemeself - Photobucket basically engine doesn't run fully choked do I need to tune it in order to run it fully choked ? check out the video thanks for helping

Hey guys got a Question for you, We have a Bird Thunderbird with a HS40 on it. It runs fine but while riding on a bumpy surface or if it hits a bump the choke lever vibrates or gets nocked into the on position, then the engine stalls out. The spring that goes in the notch is in tact but the...

So I got to installing my new gx200 bored carb on my 6.5 ohv engine. It came with the choke removed, and a screw taped in its place. Now the choke post fits when I take out the screw, but it seems now that the gigantic air cleaner body has been removed permently, there's not a way to hold the...

Hello all! I did a search to find a solution to the loose choke lever when replacing the stock air filter. I found that ARC makes a bracket but it has to be used with their adapter. However, I have a predator and their adapter will not work, to my knowledge. Any body have a solution for the...

Was looking for my pulsa jet linkage but found some good info for future seArchers on the choke a matic Choke-A-Matic Linkage

My Son comes home on mini and the speed /choke control panel is gone. Part a tiny part of the bracket under the 2 bolts is there but modt of it and the choke linkage line is gone. Using an aftermarket filter. Having a hard time finding the panel that looks like the correct one. Anyone...

I have a k&n on my clone. I need the bracket that bolts to the filter adapter to keep the choke lever in place. Anyone?

Does anyone know why? It ran fine when I first installed it but after 10 hrs it needs to be half choked and it wont idle steady.

I just bought a Baja carbon with a 6.5 hp clone, it did not have some parts. I have found a gas cap, cleaned the carb and ignition, and got it running. The clutch sticks but after taking it apart and cutting the spring about a 1/2 inch that now works ok. The issue I can't seem to get right is...

I thought that I would share this with others, so that you do not have the same unfortunate experience that my son ("The Ruppster 86") and I did last week while out off-road riding. If you have a mini-bike with a HF clone engine WITH THE STOCK AIR FILTER BOX REMOVED (i.e., you have upgraded to a...

hi my hs40 needs choke to start it then it will only run on half choke when i flip it to run position it dies and it really dosent run that bad on half choke even after its warmed up only runs on half choke :shrug: it ran that way before i rebuilt the carb does anyone know i searched this...

My hf 6.5 engine ONLY starts when the choke is off. I could ride around for a while and warm the engine plenty (with the choke on, of coarse) but if I ever kill it and want to start it again shortly after, it won't start unless I set the choke to off as if the engine is cold. Sometimes this...

How easily is the the choke lever suppose to move? It doesn't seem to stay in one position when the engine is running. Nor does the engine immediately stop when I close the choke.