choke

hand bored to the max .690+ reworked fuel circuits, jetted for pump gas. doesn't have/ need a choke. 1 pull starts. will add about 1-2hp over stock.

So I have a gx160 on my bike and just got the clutch and chain today so threw it on and the idle is too high as soon as I took the choke off it reved up and wanted to take off can't seem to find the idle adjustment on this carb

I have an old up draft Flo Jet carb from a 3 h.p. Briggs horizontal shaft engine with a broken plastic choke lever. Would anyone have a way to look up this part #? Thanks in advance for any help, John.

hey guys i have a predator 212 on my go cart and it runs on full choke but when u put it half way or full run it dies out what can i do to fix this ive tried the gas tank cap idn what the problem is. helpp!!!

I see the aftermarket or modded carbs are available in .615, or bored to .625 etc. With a digital caliper, the engine side of my stock Hemi carb measures .745 or 18.9mm. What am I missing? I'm replacing a 120cc 4.5hp yamaha engine (kids snowmobile) that currently uses an 18mm carb which is...

Hi all, My son has a go-kart we built, with a stock Predator. It sat for nearly a yr. We drained the fuel, cleaned the carb, changed the oil, and it fired right up, BUT, it will only run well with the choke on. It will idle with the choke off, but dies the instant you hit the throttle...

I bought a carb thats has no choke. Kinda wierd . I found a gas cap and it fit over the carb perfectly. I drilled 3 holes in the cap for half choke and put duct tape over it for full choke. Sent from my iPod touch using Tapatalk

Went to go start my MTD. Thing starts on a couple pulls everytime. But today.:shrug: So, I take a peek at the carb, and what????? No choke. Gone like gone, gone. Just a friggin hole sucking air.:censure::censure: So can you replace them or is the carb time for the truck? When I freshened...

Please tell me how this clip attaches so my choke lever don't fly off in the breeze. Thanks

Probably not the correct place for this but could someone point me in the direction of a choke assy for my son's 2.8 DB30 ? The lever is broke off and it wont stay open, keeps closing during riding I figure to replace it.

I put on a new air filter on the predator and I also re-jetted it. I don't got the spring for the governor rod. When i i turn it on and open the choke it goes full throttle.

Hi , guys. I have a briggs flathead( not raptor) I am building. The motor came with the carb that has pull out choke. I have access to carb without choke. Reason for wanting to use it is already has race linkage, better pick up tubes , etc. My question is can I use it? Is the a way to...

My H25 is missing the carb choke lever assembly pictured below. Any ideas where I can find it?

My stock 212cc Predator dies when choke is fully opened and I can't seem to figure out why, but only at idle. If I open the choke fully and give it throttle, it will keep running, just not at idle. It will idle if choke is less than half way open but I can't give it throttle then. Motor has...

On my DB30 the choke switch has become very loose, and the engine vibrations will move it. This is usually when I am going at higher speeds and it will go from fully off to fully on, but it often turns itself from fully on to halfway on when I'm trying to start it also. I found no info online...

I've been through this carb, replaced the rubber disk o-ring, blown air, and everything else I normally do to get carbs free flowing but this one is obviously not cooperating. I did search some other threads and found people suggesting poor gas cap venting or air leaks. I've also replaced every...

Hi there guys, I got a 3hp Briggs that has me stumped. It will only run with the choke on, and it runs poorly even then. It will rev up, then almost die, then rev back up. It has a pulsa jet carb, and I checked the gaskets, all new, no leaks. The tube from the breather to the carb isn't...

Can someone please give me an idea on how to install the choke hold bracket on a clone or even better post a pic thanks in advance

Just installed a Lifan 160F-A 4 hp in my sons DB30. IT runs fine but everytime you start it , it has to be choked.This is fine for initial cold start but it needs it even after its warmed up. WHATS UP WITH THAT ? The engines new with about 30 min. on it. :shrug:

I just installed a new 6.5 HP predator on an old style dirt bug. Started first pull. When I move the choke off and to the run position it goes to full throttle and wants to take off. I rode it down the street but it goes top speed only. Only way to slow the RPMs is back to choke. When I...