To start off, I am working on a Greyhound 212 with the governor intact and the governor spring cut to give me 4400rpm no-load. I have about 1.5-2 degrees timing advance by slotting the holes in the coil pack and moving it down. It has a Comet TAV2 that engages at 2200 rpm and accelerates at 3900...
I just got that first DB30 with the predator 212 I posted last week, and I want to start doing some mods. I really love all the headers that I see people ordering and putting on. Is this a fairly easy mod for a beginner? I'm totally new to minis, so I don't want to get in over my head.
Do I...
I have about 10 NOS Clements Racing Engine step header. $15.00 each plus shipping. Pay Pal. Header is 16" long, .930 at the engine, steps down to .825. This is a torque tuned pipe.
larger one looks to be agk smaller one is some whacked out box stock kart setup? I put it next to Briggs muffler that OldMiniBikes sells to give perspective. It tiny.
$15 plus shipping for both. OBO. Located at 10509
What headers have you guys bought and put on you fat tired Baja bikes that have the honda clone? Buckeye and me were wondering. OldMiniBikes has a good selection of headers, but which ones fit the frame the best? :shrug:
Thanks,
Clayton
:thumbsup:
Lightly used down-loop header...blasted clean and reshot with header paint...this is a down-loop header and will clear most minibike frames...$35 plus shipping.
Lightly used up-loop header...blasted clean and reshot with header paint...this is an up-loop header that will probably NOT clear...
Right now my kart has the NR racing motor with a candy cane header and RLV muffler on it, to say the least it is loud and I also don't really like how it sticks out way pat the back of the kart
Been thinking of changing to a box stock style header with a screw in muffler to cut down on the...
I just bought two 5hp briggs headers for $22 shipped, The headers were $3.49 and the shipping was $7.50. Straight headers, one 13" one 11" with washers on the end, I'll bend and weld em till they fit my applications! There are 3 left! Item #300489988528
hey guys i want to make a custom header for my 6.5 clone, and i want to make it a 2 stage header. but how do you make the step up part of the header into the next "stage" ? im also getting a slip roll for my b-day. its a small 12" one so i can also fab up some custom gas tanks too
Just been getting into Honda clone engine's. Got an old emmick frame and been building it up with alot of help from my local kart friend from affordablegokarts.com. been taking it to local tracks and just having some fun with my buddies.
Anyways, every time i run the kart for a long period...
Sorry to start a thread just for this.
Does anyone know if this header/exhaust pipe will fit a DB30? I know it will fit the HF 6.5 clone which i have but is it compatible with the DB30 frame. Is reforming/bending required or is it a bolt on and go? (sorry if the pics not there,new at this.)
Im not sure if they are made for the 6.5 honda clone, but will they fit on my db or will I have problems with the frame?:hack:
http://www.affordablegokarts.com/mm5/merchant.mvc?Screen=CTGY&Store_Code=A&Category_Code=GGPP5
I have a couple DB-30's with the HF 6.5 motors. I had these headers on them. One with the small muffler and one with the larger one. I needed my motors quite so I modified some other. I will sell all of these pictured for? They have about 5 min running time. Serious. Once I bolted them on, I had...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.