linkage

Hello, I'm wondering if anyone would have a photo of the throttle linkages for a G300 Honda. Particularly going from the governor arm to the carburetor butterfly. Matthew

sooooo... I'm trying to figure out a way to my throttle cable to the Tecumseh carb I have. I was hoping someone else here has been through this in the past and can help me out. thanks for any help I get, Lyle

Im looking for a nice blower Shroud (no extra holes) for a 1968-69 correct Tecumseh H50. I also need the correct throttle linkage used on this motor for Rupp mini bikes. Let me know whatcha got. Thanks folks!

I picked up a fox sprite a few weeks ago that had a Honda clone on it. In my guesstimating the motor that came on it was a harbor freight "greyhound". I'm not positive because I'm not actually sure I've ever seen one. Just heard talk about them. Anyway....... The po had all the throttle...

Lately ive seen a few vintage engines on ebay with this throttle linkage. Anyone try it for a minibike? Im going to try and find one. Looks real convenient.

Does anyone have a linkage setup that I can purchase ?..or thoughts about making a linkage that will work on a B&S 8HP Flathead. Gote is completely restored..Can't get a linkage to work..thanks..jv..

So this has more than likely been asked, but a search wasn't producing results. I'm using a different fuel tank for my 212, as well as an angled air filter. With that being said, it leaves two useless hoses... One that ran from the top of the fuel tank and the hose that goes from the old air...

Does anyone know how to reattach the butterfly to the throttle linkage? As you can see, I can pull the throttle linkage out because the screw came loose inside. Ive take the carb all the way down and apart but there doesn't seem to be any access to get a screw driver inside to screw the little...

I am going to use this old Tecumseh on this bike (dubbed the Flying Grapefruit by my daughter)but its got the other kind of gov linkage in place for when it had the updraft Tillotson carb. Just wondering if anyone has converted this set up to the regular one. Can I just take it all out and put...

looking for a carb and tank for a older briggs 5hp in good shape. light rust in tank no prob., I have liner for that....carb needs to have a tight choke knob and good throttle shaft. need the linkages and filter box too I have paypal, or partial/ trade i have a seat, azusa rear fender, taylor...

I purchased a throttle linkage kit from OldMiniBikes and am curious if anyone has pictures or instructions how to install it, I can't find much of anything on the subject

i bought a bike that has had some carb linkage engineering. I would like to buy all the springs, linkage bar and cable adjuster. I wanna keep the 97cc engine for my 7yr. The carb is getting replaced as well. The choke is wore out and vibrates back and forth. I currently use a spring to...

New here I just bought a Blazer and a model B Tote Gote, sold the Tote to fund build of Blazer. The carb from the model 14 Briggs was missing and some of the linkage need pic. of carb and linkage please. Anyone know where to get rubber boots for two speed shaft?

Does anyone have any pictures of the spring and linkages for the throttle. I have a 70 roadster with a broken governor spring and a bent throttle rod. Looking to see what parts I might need to buy.

I have a Duromax 16hp electric start engine I'm putting on a trike. It's missing the throttle linkage and muffler. I've found mufflers that'll work but I'm not sure which throttle linkage I need, does anyone kno? I also would like to kno which battery is recommended.

Has anyone ever had one of these engines on their bikes?? Just bought two of them for my younger cousins bikes.. Stuck on the throttle linkage.. im sure ill find a way to link it up, just looking for tips/hints/tricks!!! Thanks for any feedback!

I need advice for hooking up a throttle linkage on my honda clone mini bike

Let me preface this by saying that I have not disabled the governor yet but I plan on doing so only after I have all the necessary parts. Anyhow here are my questions. 1. Instead of physically removing the governor arm and gear from the engine, could you just leave it inside of the engine...

I need the governor linkage rods and throttle linkage that mounts to the shroud. Let me know what you have. Thanks, Jerry...

Hello! So, I have been searching these threads for about a week now and have not found exactly what I am looking for. My question is, has anyone hooked up this specific throttle linkage for the predator 6.5? I have seen other throttle linkage hookups but not any using this specific setup...