cam

So I have a 22mm mikuni carb on the way for my 212. It has 26lb springs flywheel rod isky cam. Any tips for when I get my carb? Can I just built on and start?

For sale :you pay shipping: -DB 30 front wheel good condition no bearings - $20 - Stock animal cam ( can be used in Briggs Intek 5.5hp - 6.5hp ) -$20 Will post pics later or can do via text too. PM me if interested.

Will these work in stock honda clone with bsp 2 cam and stock head? Thanks

I'm working on a project right now with an old tractor that came from the factory with a 6hp tecumseh. The engine is junk and I'm going to put a 212 hemi predator I have laying around on it. 6.5hp is 0.5 more than stock, but I'd like to squeeze as much torque out of this engine at 3600 rpms as...

What's the best way to go with briggs 206 intek with 308 cam and arc rod. Need to mod valve train right ! How much ? Spring pressure ? Valves ? Retainers ? ? ? ? Help !!! All input appreciated .

I have a carroll stream 6.5 hp clone running: 22mm mikuni carb straight pipe billet connecting rod +.020 flat top piston racing spark plug torque converter Now I need to decide on a valve train that will give me lots of low - end torque for climbing up hills but will allow me to have a...

Why is everyone out of black mamba and black mamba jr. cams? Ive heard such good things about them, I wanna try one.... Were they discontinued? If so, what is a similar performing cam to go with?

I have a non-hemi predator 212 and I'm looking for some upgrade advice. I have a 22mm Mikuni carb along with the curved intake manifold and angled air filter, racing spark plug, 18lb valve springs, billet flywheel, superbox exhaust(without muffler), stock cam, and stock rod. With this set up...

Is this cam able to be used with stock springs, rods, and flywheel?

gx440 block 69mm stroke 4.450 rod flat top 92mm piston that's what I got so far.. I need ... cam flywheel head rockers nr racing sells a gx390 head 40 mm intake ? I'm also looking at raceseng 1.8 fly wheel and the 356 cam from nr racing still clueless about rocker...

Hi guys, here are some of pics of my latest project. I don't name my projects therefore the title. It has a briggs animal with .060" shaved off, billet rod, .310 cam with 1.3 rockers, a mikuni tm28 and as you can see a torque converter. The goal is 70 mph in the 1/8 mile on gas.

Hi folks, I aquired this engine some years ago, I suspect it's an older model as it has the 2 prong lead for the spark plug, It was probally a tiller engine at one time because of the cam driven shaft which I cut off flush, I will be using it on my Harrison project, numbers are as follows...

So I've done a combination of about 6 of the hemi motors with stock, 20, and 40 thou longer rods. I ran into a problem with the 40 thou longer rod hitting the middle of the cam between the lobes. Eh....anyone else have this problem?

Noob question but does a aftermarket cam add compression ? Approx how much ? what kind of rpm does a cam add ? I'm debating on a cam 2000- 5500 or a cam for 7500 rpm .. 7500 needs 10:1 or more .. so questions are how to add rpm along with compression to satisfy the build ...

I recently built a clone with all the goodies , cam, springs,arc rod,flat top piston, anyway I ran the motor for like 20mins then I notice it was leaking oil out the side cover gasket. I removed motor from the bike and broke the engine down , I wanted to check torque on rod & switch cam &...

Got a new Predator, and decided to tear it apart. Its down to the bare block, plugged all of the holes from the governor (2) and oil sensor. Just got a, Isky Black Mamba cam and springs today. Installed the new springs. Waiting on the billet rod, flywheel, Mikuni carb, manifold, jets, and...

I took out the gov. the cam came out when I took of the side cover. I am sure that I lined up the dots on the cam. So I installed a throttle plate and put the motor back in. Stars fine, runs fine on choke but dies when you turn of choke. Sounds like high speed lean out ? took out carb. cleaned...

Figured I would post some pictures of my latest all out flathead build, Should make some real good power when I get her dialed in when the warm weather comes! Does anyone have experience in timing a dual plug? I have some ideas.... It has full port and polish eyebrow removal Dual spark plug...

I put a 94ss dyno cam in my 5hp briggs with a billet rod and billet lifter the motor starts but screams for about five seconds then dies I was thinking of advancing the timing to see if that helps if anybody can help me out that with any ideas on what I can do to remedy this problem

anyone have a spare Dyno 94-SS cam just laying around?