problems

ok so i removed the throttle assembly plate and all the springs and stuff and marked it so they go in the same spot then i put it back together and now the throttle on the carb is any where to 100-50% open all the time and i dont know what happened i just cant figure it out any help is appreciated

Hello everybody here on the more than 2 wheels i`ve got i little problem with my rear rim are should i say a big problem it blow completely in pieces i`m looking now for a new rim for my Broncco gokart project i`m looking for a 5 inch rim at the rear with a pickup for my chain can anyone...

Hey guys, I'm a newbee here. Nice forum! Anyways, I picked up a little Doodle Bug for $100. It was only a few weeks old. The owner was frustrated cause he could never get it to run well. Idles but dies when given gas. I've played with the mix and the choke and I can't get it to run very well...

I ordered brake cables and a decal kit for my rupp. It all came. I started looking at the decals and one of them is so old and in ruff shape it is not even useable. It also has no adhesive left to it. So i emailed him and after a week he emails me back and said he would send me another decal...

Hi there guys, I've been having some trouble with the carb on my Tec H70. I've rebuilt it with a carb kit, and I made sure I did it properly, I've checked the float to make sure there are no leaks, all the gaskets are good, and it still doesn't continue to run. It will fire right up when you...

Well as u see from my other post the engine kept getting stuck and i figured out that it gets stuck when i put gas in the gas tank so it will be fine buy poring gas into the carb but if i put it in the gas tank it wont start and then it will get stuck

I have a db30 and I put a 6.5 (clone) and it gets up to 45-50 and it just stays at that speed and dosent go up at all I tried a bigger carb but same problem Any suggestions on what to put in it :shrug:

stock predator. the air cleaner cover falls off all day long. duct tape or....??

my predator pullstart won't engadge until it is almost all the way out. i get a 6 inch pull and im afraid i will break the rope. will the old clone starters fit? and it stalls all the time at idle :doah: the rpm's are up to just before the clutch catches.

Always use tracking (delivery confirmation) no matter what with usps this is a package I sent to Lake Havasu City Left Kaysville UT on the 4th Denver CO on the 5th Jacksonville FL now in Bell Gardens CA, Im expecting Anchorage next.... Go ahead and track it 0312 0090 0000 1467 6982 With...

Okay got my big block running today . Had carb apart and let it soak in carb cleaner for a week , put it back together and it runs like sh-t . ??? is should i by carb kit or new carb .

alright, so ive got an older 5.5 hp o.h.v. briggs. it starts when i choke it and runs for a little bit, then dies when i open up the choke. and ideas of how i could tune it so it dont die on me? it would be greatly appreciated. thanks

ok so i got my 5 hp briggs motor off graigslist for 30.00 bucks. found it to be a very tight fit, have to run a different exhaust just to fit in the frame. when i posted in the what is it thread some said its a bronc vt3 does that mean it had a 3 hp motor? i will clean up the motor and i have...

Any ideas why this rope is not recoiling all the way in?:shrug:

I have a 5hp briggs and stratton engine that i have in my mini chopper that has been giving me some problems. When i ride it in high rpms (4900-5200) the motor skips a spark. also it takes a while to reach high rpms with my 6 to 1 ratio and 16 inch tire. i tested the compression and the highest...

Last year I bought a newer tecumseh 3.5 hp minibike. We rode it alot last summer and changed the oil and air filter and last summer it was running good for the most part but a few times the centrifugal clutch would need lubricated and one time I started the bike and it actually took off and...

Trying to put music on my buddy's ipod off of my computer and my computer is only recognizing the ipod as a camera. Any ideas?

Here is a good read on the shafting we are getting at the pump buying E-10 (10% ethanol /gasoline blend sold everywhere as gasoline). Oh yea and you subsidize it like everything else..... Fuel School: Phase Separation in Ethanol Blended Gasoline Jim

Ok here is the motor I need a side cover gasket for First I ordered this one from BMI which says it was for the clone and no more detail That one does not fit, everything fits correctly except the bolt hole in the bottom right corner I then ordered one for a GX200, it was...

I have a Tri-Sport with a Tecumseh engine and a variable belt drive. I believe this power unit is original to the machine. I don't know what model/HP the engine is, but if it matters, I can find out and post it. The center distance between the drive/driven pulleys is 6-1/2". Here are a few pics...