screw

I am a proud new owner of a 1974 Harley Davidson X90.. After cleaning the carb I can get it to run with the Choke pulled up but it dies as soon as soon as I close the choke. The mixture screw does not have a little rubber O ring and small washer on the end... I know not all carbs do but the...

Hello everyone, long time lurker, first time poster. Lots of good information and people to be found here :) Please bear with me if I refer to anything with the incorrect names/terminology, I'm a newbie when it comes to this stuff, but I'm here to learn! Well, I purchased a "home made"...

I have a 6.5 HP 196cc Coleman ct200u, and I have no idea how to adjust the idle. I've been having a few problems on my bike, (backfiring, stalling with throttle, excessively long warm up time, backfiring on deceleration, running better with the choke on, sloppy idle) and I think most of them...

I have a 6.5 HP 196cc Coleman ct200u, and I have no idea how to adjust the idle. I've been having a few problems on my bike, (backfiring, stalling with throttle, excessively long warm up time, backfiring on deceleration, running better with the choke on, sloppy idle) and I think most of them...

DB30, 6.5 and 11HP Clone's Where is the best place to buy the Throttle Swivel with Screw ? I now have a 11HP and a 6.5 that don't have one and I need them. Thanks to those that reply :thumbsup:

Something isn't right. I put a new carb on this HM80. It will run if I screw the needles and all the way in but it backfires a bit. If I idle it up it is worse. If I try to back the screw out it starts to die. I think it is running too rich with the needle all the way in. Maybe I got the...

Does anyone know where I can get a Governor stop screw for the stock engine? I searched and could not find it. I just picked up one of these for cheap and I want to be able to restrict the top speed, but the screw is missing. I am going to get the Jackshaft from Pro Mod and otherwise keep...

i just finished swapping a 10hp Tecumseh from a snow-blower into my go kart. i fully cleaned the carb and have the throttle hooked up to carb with out governor. it starts easy and runs great but i cant get it to idle low enough to fully release the torque converter. if i turn the stop screw down...

Hey everyone. Very very new to mini bikes. I bought a frame engine etc and I took the tires off so I can strip and repaint the frame. Now I'm trying to put the rear tire back on and I slide the screw into the frame through the tire and put the bolt on. However the tire slides left and right on...

Was wondering why the idle is so high cant seem to figure out how to adjust it, the screw is set where i want it but the throttle is half open

Im doing a 73 5hp briggs engine for the build off an.im.stuck the bolts on my carb an tank wont budge they are stuck on an the screw driver is stripping the head I dont know how to remove these do I.use pb blaster on.it can I.use a little heat on them or a screw extractor tool to.remove I.need...

So I thought I got all of the bearing out of these wheels by hammering lightly with a long screw driver from the other side. But did I leave an outer casing there or something? And I can't get to it from the other side cuz there is a rise or like a ledge behind it. OR is this part of a very...

Well, got the motor started then I adjusted the idle screw on the side.....then,I went underneath an messed with the mixture screw an,that's when things got messed up Ok , 1st thing that happened was motor was running while giving it a little gas it Boaged up an died then wouldn't start...

I have read this forum alot and this is not a question on removing the governor, etc. My motor is stock. I was reading and it seems a lot of people remove the throttle set screw to get a few more rpms. I hooked up one of those cheap tach/hour meters to my bike, It would idle about 2k, and hit...

I've got some new tires and tubes on order and I'm wondering what you u guys use to install them. I imagine minibike tires are real stiff when they're brand new. I cant imagine using a couple of screw drivers like I would a bicycle. I'm thinking I could bring them to a place like Goodyear...

I am going to put on a new exhaust pipe on my H60 and I noticed that there are threads in the exhaust port. I had a couple pipe fitting at my house so I tried and it screwed right in. Is there any advantage or disadvantage to running a strait pipe screwed in vs. a bolt on strait pipe?

http://www.bajamotorsports.com/documents/DB30_QuickStart_Guide.pdf

I stripped out the set screw hole on my clutch, the one that screws into the key, the other set screw is in nice and tight, is this set screw that important, once I screw in the bolt at the end of the shaft, the clutch won't be able to slide off. Do I need to re-tap the set screw hole or do you...

Hey all, getting closer to having the tote goat running decently but I've run into a snag. I had the engine running (read: idling) well, but when giving it the throttle, it'll accelerate for about 5 feet and then the engine starts hesitating. If I stop and let it idle for a bit, I can get...

Hi all, I'm having a really hard time finding the throttle limiter screw on my 2.5hp lifan engine. It is a 2012 model. Sticker on pull start says Yukon trail. Any help would be appreciated Sent from my LG-P930 using Tapatalk 2