carb

Do the 22mm Mikuni carbs require you to use a pulse pump?

Just like the title says, I need the Tec part number for the linkage rod that goes from the governor to the carb on a HS 40 engine. I think it might be 32698 , can anyone confirm that # for me ?

Real never used brand spanking new carb. $75 shipped

This is a good service reference for troubleshooting pre-emission and emission-compliant carbs (covers OHV). Hits the variants of Briggs tank-mounted carbs and float-bowl type carbs. Useful for any brand engine...

Does anyone have, make or sell a 20 degree carb wedge? I have Rupp's with the slanted HS40 engine. I saw on old post a while back where a guy was selling 20 degree wedges that go if front of the carb but can't find the thread. They were cheap like $10 shipped or something like that. I can't...

I need a carb and intake for a Tecumseh H 50 radams7425@aol.com

I would like a little help, I'm new to all this but I managed to mount a small flojet off from a Briggs 3hp and put it on a 5hp Briggs of about the same age my question to yall is can I hook the arm style governor that the old gas tank carb used up to a carb that was on a motor with a pneumatic...

Looking for the carburater bowl fuel adjusting needle, spring. (On the bottom) I cannot locate mine and I need one. Any help or leads are appreciated. If someone has a complete carb. That's junk other wise let me know too. Thanks.!

So I received an aftermarket replacement carb from Amazon.ca, and the carb I received is missing the port on the front (the one that the spacer gasket has a cutout for). The port is pictured on the website, so my question is, was I sent the correct carb? Every image or video I've seen for the...

My clone has a straight pipe, mamba jr cam, no gov. Is it possible that the mikuni 22mm is too small? Given the chance, I think my engine would suck the air filter right through the carb. Sometimes this thing works like a champ, other times it's as if it's struggling to keep the engine fed...

I have a Tecumseh 10 HP HM100 that is missing a carb. I want to try one of those cheap aftermarket carbs. Can anybody provide me with a link to a reliable Ebay seller that you have purchased from before and the carb performed properly? Of course I only want a fully adjustable (both high and low...

Here are some pieces I will never get around to using. These parts will allow the use of an old style Briggs filter on a Tec or Tillotson carb set up! Fool your Briggs friends with this one! The polished center piece allows you to hook up to your breather! Looking for $35.00 shipped, or add the...

I just bought 2 baja warrior mb200's with what I believe are mb165 engines. The bikes were used hard and I've slowly been fixing them up. I finally got to cleaning the carbs and when I pulled the first on off I discovered that the bowl was held on by what looks like a rivet rather that the...

A friend of mine needs a manifold for a PZ 22 , I don't have one to model . What I need is the flange dimensions , throat size and mounting bolt spread , and a pic would be nice .

Got another Murray track 2 with a old style predator 212, did a carb job on it. It's idles perfect on choke, take choke off dies, without 3/4 to full throttle. I know this has happened before to other ppl. Did the search up top, looked through 10 pages couldn't find what I need, so this...

Hey! I had a perfectly running 212 on my db30. Well I upgraded my carb today to the bored carb from OldMiniBikes and it wouldn't start until I held the throttle open...once it starts it won't stay running. If i give it gas it dies...I've tried messing with the choke in all positions...no joy. I have...

For sale is a intake manifold to put a tech carb on a Briggs 5hp motor . And to help sway buyers is a custom throttle setup to make this combo work . You only need a carb and cable Clevis , not getting mine . Price 35.00 shipped

Good Evening Everyone, I am looking for some troubleshooting help with using a stock carb on a modified preadator engine. First, this is not on a minibike, but a motorized bicycle that I race occasionally here in southern california. The rules for this engine are stock rod...

I got a Bug go kart with a Tecumseh H30 that I can't get to idle. I have a few questions about getting it to work. Wich way does the diaphragm go? Does the diaphragm go against the carb then the gasket followed by the cover plate? My carb says F3 by the air filter and then says H where the carb...

Anyone know where i can find this intake?