light

This is an original, used, Gilson tail light piece with wire attached. The new Speaker cover does not fit it well, but could be siliconed on? The gap cap is from an original Gilson, but has been rechromed. The cap shows signs of pitting still, but comes with the plastic seal/vent. Looking to...

Looking for the upper forks/triple tree with headlight/number plate mounting ears, for 1971 Speedway with 10" wheels. Please let me know. Mike

i just mostly finished my project, i put a predator 212 hemi in a small enduro frame (street legal) i found the lighting coils for the predator at several places, but no flywheel, and i found a thread from another forum during a random google search, somebody claims to have used a 3 magnet...

I bought the head light and the switch knobs were broken. What are the correct switches to replace them with. It had 2 switches with on/off and high/low. I already have a replacement lense on its way for it. Thanks for all help.

There's a machine shop down the street from me so we're going to keep him busy.:smile: Note: This can be used for a trike. Like a meter maid thing. Retro. Not making long jumps with. Anyhow there is a gap here to be filled. A junkyard rearend from a micro car is too heavy. Might as well...

Need Speaker headlight bracket and complete tail light assembly. Might consider Arctic Cat parts...

Trying to wire up the lights on my trail horse which is a first for me. Tail light has a brown and red wire headlight has 2 whites. My engine has the standard plug with the red black and green. I was planning on running The brown from the tail light , one white from the headlight and one wire...

So I was wondering if I had an old vw pressure switch and I have a dual element tail light , would that give me a brake light? Someone who knows anything about this would be delightful . Thnx in advance kenny

Need a brake light switch for a 1968 Rupp Disk brake bike. Thanks for looking! joel

I need two Rupp brake light switches for disk brakes. Is there an alternate source? There are two on each rear brake assembly. Part # 12984 and 12985 ( #82 and 82A in diagram) 1968 Rupp Minibike Part # Catalog Thanks for any help and suggestions! For the engineers - How do these work?? :)...

Said, I would never sell this, So get me before I change my mind :laugh: 1973 HS40 with charge coil, Runs and lights perfectly, Bushing crank 450.00 US Plus the Ride / shipping You have no Idea how hard this was to post, LOL

Good afternoon Anyone have a suggestion for turn signal/brake light for a coleman ct200. Thanks

I'm looking for 68 Rupp stop light switch # 12984 , actually I need 3 radams7425@aol.com

Perfect NOS condition. I have 3 available. $25 bucks each shipped, paypal only please.

I picked up a nice Roadster2 with a working headlight system :-) It needs a brake light switch. There are just two wires hanging near the brake lever. I see a Roadster2 has a different part number for the brake cable. Is the switch built into the cable? What years used the small seat lettering...

Looking for a tail light and clutch guard for a Trail horse. Thanks Bryce.

I'm adding lights to my trail horse. I've seen a lot of light switches for turning on/off the lights (hi/low beam). Got my tail light installed but wondering how to hook up the brake light. Did the trail horse mini bikes have a brake lever with a switch that triggers the brake light.

Looking for a working head light that came with the BC, MX and CS bikes. Thanks. Tom

Hope this is the section for the post..So I have a completely original 1970 Rupp Roadster. The headlight and tailight are very dim, to the point of barely seen. Have gone through the wiring connections and replaced the headlamp as original was burned out. Could the lighting coil be an issue...

Is there LED luring that would work well with an HS50 lights Tec motor? There are 2 lighting coils, 2 amps each.