remove

Hi all, new member here. About 2 months ago I got a Baja Warrior from a local Tractor Supply Co to have some backyard fun! I loved the riding style/feel of the Warrior and it did very well in the backyard "tracks" I have tried so far. The stock engine (Honda GX200 clone) almost always started...

I am trying to install the jackshift kit. I did get the bolt off in this is a newer style Doodlebug. I also took the snap ring of the clutch and remove the cover. Is there anything else that could be holding this clutch on? I don't see anything else no bulbs are hidden nuts or screws. I blasted...

why is there a resistor in my spark plug boot, and should I remove it?

I have a Bonanza 1300 that has an incredibly loose fork. I replaced the bushing already. I have measured out the bolt hole in the top plate of the fork where the head bolt goes and it seems to be worn out a little bit. It measured out to .654 where the bolt measures out to .622. I have...

At some point someone coated the inside of my rupp sprint gas tank with this cream colored sealant .im not sure if it started peeling off on its own or if it reacted with the methanol I put in there but it needs to be removed. Any suggestions? I am currently rejecting any suggestions involving...

I'm trying to remove the rear wheel bearings from a 1972 Rupp Roadster but they're not moving and I didn't want to force them. Any suggestions/tricks on how to remove them?

I have a question,and I asked the same in My build off thread....Has anyone cut the top of a predator212 piston and used a .020" longer arc rod to end up with 0 deck height?....I have the tools to measure everything,just have to go through the r&r of the old rod/piston deck height,then the same...

Title says everything. Im thinking about removing.the 2speed to get increased speed with a 1speed...

Is it just tapered? If so how do you get it off? I read some of the older ones were threaded and tapered. Anyone take one off and how?

Ok I am at a loss. I have the entire bike apart for restoration, but I can not figure out how to get the chrome lower fork legs out of the fork. Is there a trick to it? Thanks Josh

I've searched the internet and this site for similar questions but everyone just seems to have a problem pulling off the clutch once the bolt is removed. My question is how do remove the bolt? The whole shaft spins and I'm not sure how to stabilize it. Do I need a special tool? I bought...

It is on a Tecumseh OHV 6hp engine. There is no set screw to remove and it won't budge. Any help would be appreciated!

I recently purchased a 64 Tote Gote model 404 and have been trying to figure out how to remove the rear wheel. I can easily remove the right and left bolts that free the axle but there does not appear to be any way to loosen the slack in the chain. Is there something I am overlooking or some...

Well i took the side cover off what i thought was a stock briggs 5hp to a cam change and realized that it has a billet rod and lifters. The crank also has a ball bearing on it, how do i get the bearing off and put it back on so i can change the cam. Also the cam has no markings on it at all does...

I would like to remove the gas tank from my predator engine and add a custom one to the frame. How would I do this? I cant figure out how to remove the gas line from the carb

Ok, I'm trying to get a clutch of a briggs 3.5 hp. It is an older clutch that had a small bump in where it goes on the shaft from someone pounding it onto the motor. I put the clutch on only about a month ago so it shouldn't be rusted on. I put the clutch on backwards, so my puller won't grab...

I feel really stupid for asking this question, but how do you remove valve springs? I am rebuilding a 2.8hp DB30 engine and have everything else removed except them, any help would be greatly appreciated.

Hello, I've never removed a clutch before. On my go-kart, I've never needed to do any maintenance because it has a torque converter. But my Jiangdong engine that's brand new is leaking oil and I need to remove the clutch and plate to see where exactly it's coming from. So, I guess I need...

I have a briggs 3 hp and I need to remove the clutych off the shaft, It is not budging and I am not sure how to remove it. I do not have a gear puller

i know i've asked this before.. but i guess what i really need is some pictures of how to remove the crankshaft.. i'm afraid i'm going to do something wrong and mess up my engine. any help would be greatly appreciated. thanks