valve

40$ shipped can also mount an exhaust brace onto the bottom of the valve cover etc.. pretty sweet

I have abused Briggs 5hp Fun Power engine I am trying to get running. After I got the valves out (wasn't easy, another thread) I noticed the end of the valve stem that rests in the keeper was badly worn. 1st I thought should toss the valve, because excess wear could effect valve lash. But...

What is the best way to set valve lash on a Briggs 5hp? Like what is the best way to take material out to open the valve lash? File? Sand paper? I have seen the block of steel with the hole in it and the you lightly sand material away to achieve the proper clearance but I do not have one. Which...

The real deal... an MDB 32/28 big valve head. Welded, ported, milled.... dual springs, retainers, ready to rumble. I bought this with big intentions, but another project has come along & I need to make some space. Payed $350, asking $300 shipped. Paypal or USPS MO...

I went out and started all the mini bikes to get them ready for some riding time over the holiday. I found that my one h60 wouldn't idle even after cleaning the jet so that meant only one thing ---stuck check ball. I shook the carb and sure enough no rattle. I soaked it over night in gas...

Looking for an intake valve for a tecumseh HS40'/HS50 PART #32644A. Prefer that the valve be NOS, Thanks Rick

Heres three tools for redoing the valve guides on various small frame briggs engines, including the 5hp flathead. one valve guide counterbore reamer #19064 one bushing driver #19274 one finish reamer #19066 All you need is a #19191 pilot bushing to complete the set. There is one on ebay...

OK, so,,, are the Raceseng 32mm ones real shallow? Any issue with drop-outs? A 14cc new casting, with a 31mm hole, same depth as stock seat, gets through the casting. It was no biggie to weld the outside, even with the porous casting, and get a seat in. Epoxy in roof.

In my gx200 build I'm going with stock valve train with 1.3 rockers and 18lb springs from agk. Do I yank the intake valve seal to gain some installed height and prevent coil bind? Also I read that only the 160s have the seal...Truth? Are they important to have? Thanks!

Hi, I have a new later model H50 short block. The intake, valve guide looks like it wasn't pressed down all the way, and will not help keep the valve spring cap centered. The exhaust looks correct. Funny thing is the old block was the same way. I have punch that looks just like the Tecumseh...

I wanted to replace my stock valve springs to eliminate high rpm valve float. I talked to one of the techs at one of the performance companies an was told that the 18# springs aren't as good as everyone thinks and that I would be better off with the trick springs. He said the trick springs...

looking for a good used or new intek valve cover

Wanted: scissors type small engine valve spring tool ( used,working) Not the C-Clamp type.

im trying to take the valves off my build briggs raptor3 5hp motor ...the bottom of the valves look like they have a c clip holding them on to a aluminum retainer how could i remove then is there a special tool my valves need lapping bad

I am running a cl1 dyno cam with 18lb. valve springs and im still using stock valves and valve spring retainers. I am spinning around 6300- 6400 rpms. Will the stock valves and retainers hold up to the capability of the cl1 cam and 18lb springs? Any advice was would be appreciated- i dont want...

What is the stock valve lash (In Thousandths) for a gx160 motor? i need the correct specs for the intake and the exhaust. Any help would be great

Lets just say. . .I did something stupid while installing a pulse fitting today. Haha. So I'm in need of a 5 bolt valve cover for a 6.5 blue HF motor. I don't know if there is a difference between the blue L shaped motor and the older blue motor, but I have the L shaped one. Need asap. I know...

Installing valve stems and mounting tires.

Installing valve stems and mounting tires.

Installing valve stems and mounting tires.