installed

I put this together about a month ago. Works well, especially off road in bumpy areas...Replaced original base with 3/4" plywood, bolted 2 valve springs to it with fender washers and lock nuts on the back side, bent a right angle in a 6" T hinge for the front and added a piece of 1/2" plywood...

Helping a friend build a Warrior. He bought a new roller that is complete less the engine last week. Yesterday he bought a new 420cc Predator for it. Now we have to make it happen. Anybody have one of these combos? I think it will take a little work but I think it will be pretty straight...

Got it with the intention of using it but I'm downsizing and this engine will not be used. Has a scratch on the air cleaner cover but otherwise shiny new. I got a powersport throttle for it and it came with an NOS Taylor curved muffler with directional tail pipe. PM me for pics or I'll post em...

At the moment, I'm mostly having trouble with the throttle cable. If you've done this, what did you do? Did you use the stock cable? Did you purchase a new one? Can you use a standard screw cable clamp under the slide? Did you solder a ball on? How did you route the cable to a vertical position...

This is a Baja Heat with a mechanically stock 212 hemi & TAV-2. I swapped in a 35 jet & an Etube from OMBW, an ARC/RLV exhaust & filter/adapter w/ clutch lever bracket. It won't idle with the choke fully open & part throttle is kind of sputtering. I'm sure I have an idle circuit issue...

I installed a predator 212 on a go kart project I'm working on and I got a stage one upgrade kit which includes 36 & 37 jets and a larger emulsion tube, when I installed the air filter kit it was so lean it wouldn't start so i swapped in the 36 jet and it ran good, then I swapped in the larger...

I was wondering how this works. Anyone know or have a pic of it installed. http://pages.ebay.com/link/?nav=item.view&alt=web&id=311374786947

Hey OldMiniBikes, Last Sunday i picked up a 1966 Taco 44 mini bike in somewhat okay - bad shape. It had a 5hp Tec on it that did not run. There was a substantial hole in the rear of the frame, the swinging arm suspension was welded in place, and also bolted. Every bearing on the bike was original and...

Ok guys, I need some guidance here. Now this is my first ever mini bike so be gentle lol. Replaced the original engine with a 79cc Predator, also bought a new centrifugal clutch to fit as it was a 5/8 instead of 3/4. Now the original clutch slid right off no problem, but I think the new one is...

Building this bike for ME ! Hope I can get it done before someone wants to buy it. Started with a frame that needed some work. Needed the neck cut off and a new motor plate was added. The frame is painted Satin Black. I had a swing arm but it was the wrong one for the bike so I modified it to...

I have a 1968 Fantic Broncco Tx-3 with the Aspera motor. The motor turns easily and I think nothing is really wrong with it other than it has sat for nearly 20 years. I've cleaned it up, strip off the paint, installed a kit in the carb and also installed new coil, etc. I really need to find...

Got a new Predator, and decided to tear it apart. Its down to the bare block, plugged all of the holes from the governor (2) and oil sensor. Just got a, Isky Black Mamba cam and springs today. Installed the new springs. Waiting on the billet rod, flywheel, Mikuni carb, manifold, jets, and...

I installed an NR racing stage II kit in my Honda GX 270 . It included a cam /springs 4 degree key, intake manifold, air filter, a bored 390 Gx carb plus Robertson H loop exhaust system. The carb is 23.5 mm bore a .037 main and a .025 pilot with a stock E tube . The kit installed easily and the...

I found this at OldMiniBikes warehouse. Has anyone bought and installed one before. and is it worth buying. And can u run this kit with the governor installed or do I need to remove it before installing it. Please help

I recently installed OldMiniBikes's 8 inch header and angled air filter on my GX160, I already have a 140 emulsion tube and a .36 jet installed and the motor runs fine but the spark plug is really black and I am assuming it is running rich, this was both tested on a NGK BRP6ES and an Autolite AR3910X...

Finally picked up some chromoly pushrods and guide plate. iv been running the stamped 1.3 rockers and black mamba sr on stock pushrods for awhile. wen I installed the guide plate it raised up the rockers should I get longer pushrods or did I install it wrong lol or should I get the rs guide...

Hi there, I am new to the minibike thing and I bought an old Broncco and after measuring the engine plate, I found that a 6.5 212 Predator would not fit on my application due to the clutch not lining up with the rear sprocket. I previously installed a 79cc on my daughter's go kart with a...

I bought a monster moto mmb80 camo at sears on sale ($100 off coupon). Went to HF and bought a 212cc hemi predator engine (with another coupon). Installed on to monster moto, I had to do the following for all this to work. Installed 11 tooth 3/4" clutch. Installed ARC Big Bertha Clutch and...

I've seen it mentioned from time time that side exhaust engines were not used on mini bikes, I in fact believed that up until a few years ago when I was researching a particular bike and was doing more than just quickly scanning over brochures or advertisement that someone had taken the time to...

Ok so I finally got my replacement rocker stud in that I broke, I set the motor @ TDC installed the 18lb springs and set the lash at .002 intake and .003 exhaust which I will admit is the smallest valve lash I've ever seen. I got it all put back together and now the motor is EXTREMELY hard to...